“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10109047
Manufacturer Communication Number: TSB 16-0129
Summary
Some 2011-2016 Fiesta and 2012-2016 Focus vehicles equipped with a DPS6 transmission may exhibit intermittent concerns of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated Check Engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013 and/or P0606 will be present or stored in the powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.
FORD:
2011-2016 Fiesta
2012-2016 Focus
This article supersedes TSB 16-0044 to update the Title, Issue Statement, Service Procedure and Part List.
ISSUE:
Some 2011-2016 Fiesta and 2012-2016 Focus vehicles equipped with a DPS6 transmission may exhibit intermittent concerns of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated check engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013 and/or P0606 will be present or stored in the powertrain control module (PCM) memory.
ACTION:
Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE
With the release of Customer Satisfaction Program 15B22 if a vehicle is being serviced using this article, the PCM/transmission control module (TCM) reprogramming and clutch adaptive learn strategy updates required in 15B22 are completed. Therefore, it is not necessary to perform 15B22 separately and 15B22 should not be claimed. It will be closed when the labor operations for this article are claimed.
- Is the vehicle a Focus built on or before 5-Nov-2015 or a Fiesta built on or before 27-Oct-2015?
- Yes – proceed to Step 3.
- No – proceed to Step 2.
- Is the vehicle a Focus built on 6-Nov-2015 and through 9-Mar-2016 or a Fiesta built on 28-Oct-2015 and through 27-Jul-2016?
- Yes – proceed to Step 5.
- No – this article does not apply. Refer to Workshop Manual (WSM), Section 307-01 for normal diagnostics.
- Does the customer indicate at least one of the following concerns are present: Intermittent loss of transmission engagement while driving, intermittent no start, intermittent loss of power, Hill Start Assist is Not Available or Parking Aid Malfunction/Service is required displayed in the instrument panel cluster (IPC) message center and/or transmission PRNDL/PRNDS gear selector on the instrument cluster flashes?
- Yes – proceed to Step 4.
- No – proceed to step 5.
- Connect Integrated Diagnostic System (IDS) service tool or an equivalent scan tool, check for DTCs. Are DTCs U0100, U0101, U1013, and/or P0606 present or stored in the PCM/TCM memory?
- No – proceed to step 5.
- Reprogram the PCM/TCM with the latest calibrations using IDS release 102.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
- This calibration installs DTC P0606 a new TCM internal failure code. Refer to WSM Section 307-01 as required. Always resolve any vehicle low voltage concerns before replacing a TCM.
- Perform the TCM adaptive learn strategy.
- Adjust the vehicle clock as it may have lost time during the reprogramming process.
PART NUMBER | PART NAME |
AE8Z-7Z369-F | Transmission Control Module Kit |
16 Affected Products
Vehicles
MAKE | MODEL | YEAR |
FORD | FIESTA | 2011-2016 |
FORD | FOCUS | 2012-2016 |
FORD | FOCUS ELECTRIC | 2012-2016 |
1 Associated Document
Manufacturer Communications
TSB 16-0129
https://www.nhtsa.gov/recalls?nhtsaId=10109047
MC-10109047-9999.pdf 102.463KB
NHTSA ID Number: 10205009
Manufacturer Communication Number: TSB160044
Summary
DPS6 – no start and/or transmission engagement or loss of power with DTCS u0100, U00101, U1013, U3003 AND/OR P0606
1 Associated Document
Manufacturer Communications
TSB 16-0044
https://www.nhtsa.gov/recalls?nhtsaId=10205009
MC-10205009-9999.pdf 102.864KB
Reprogramming
Service Information & Reprogramming
Module Reprogramming
Diagnostic Software | Interface Device | Complete Vehicle Diagnostics | Module Programming | ||
1996-2017 Model Year |
2018-Present Model Year |
1996-2017 Model Year |
2018-Present Model Year |
||
IDS/FDRS | VCM, VCM II, VCMM | X | X | X | X |
FJDS/FDRS | Compatible J2534 Devices (Including VCM II and VCMM) |
X | X | X |
Detailed system requirements, installation, and support information for each product is located under the diagnostics tool support tab for each product.
Integrated Diagnostic Software (IDS) / Ford Diagnosis & Repair System (FDRS)
For use with VCM I, VCM II, VMM and VCMM hardware devices only. The complete factory Ford Motor Company vehicle diagnostic tool that provides complete dealership level vehicle diagnostic coverage for all 1996 to present Ford, Lincoln and Mercury vehicles. The IDS software includes time based access to the IDS software, software updates and calibration files.
Ford J2534 Diagnostic Software (FJDS) / Ford Diagnosis & Repair System (FDRS)
For use with compatible J2534 hardware devices. FJDS software provides Ford Module Programming functionality that covers 1996 to present Ford, Lincoln and Mercury module reprogramming functions, plus complete dealership level vehicle diagnostic software for all 2018 to present Ford and Lincoln vehicles. The FJDS software license includes time based access to the FJDS software, software updates and calibration files.
CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool | |
CarDAQ-Plus 2 Diagnostic Code Reader and J2534 Programming Tool | |
CarDAQ-Plus | |
CarDAQ-M | |
VSI J2534 ECU Reprogrammer | |
Latest Calibration Information
Module Build Data (As-Built)
Use VIN to obtain As-Built data
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- 【As a multi-protocol Pass-Thru vehicle interface】MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
- 【MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro】Autel MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. The functions are NOT universally compatible. Please send VIN number to 🚘jmxd2022@outlook.com📧🚘 to check compatibility before your order. If need any supports, Please contact us.
- 【Wireless with advanced networking functions】Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable. Autel MaxiFlash Elite is compatiable with MaxiSYS MS908S, MaxiSYS MS908S Pro , MaxiSYS MS908CV, MaxiCOM MK908, MaxiCOM MK908 Pro, MaxiSYS Elite, MaxiSYS Elite II and Personal Computer
- 【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 【Supports simultaneous communication Definition in J2534-1】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed.Rugged aluminum case with non-slip rubber end caps, capable of withstanding harsh environment.
- 🔥【The King of Cost-Effectiveness From Autel】Fully upgraded from Autel MaxiSys EliteII /MS908S Pro/MK908P, Autel Scanner launched 2023 Newest 🅰🆄🆃🅴🅻 MaxiSys Elite II pro. 👉2 Years Free Update, ECU Programming&Coding, 38+ Service, Bidirectional Control, etc. Auto scanning 2.0 with all hardware parameters upgrade, provide total 8 (5+3)x diagnostic speed ✅CAN FD/ DOIP protocols support GM MY2020+ models, BMW E/F/G, Jaguar, Land Rover makes (Elite II can’t).
- 🔥【OE-LEVEL J2534 ECU PROGRAMMING & CODING】Enhance your diagnostics with the Elite II Pro J2534 Reprogramming scanner. This cutting-edge auto scanner supports : 1) program the new adaptive data to the on-board modules 2) replace the existing software/firmware in the ECUs 3) match the component control modules after repair or replacement 4) flash the hidden functions and 5) enhance the vehicle features. Experience 5X faster communication with SAE J2534-1 & -2 compliant programming interface.
- 🔥【38+ Maintenance Functions & High-End Functions】Autel scan tool Elite II Pro shares the same functional and deep service functions with other high-end scanners such as MaxiSys MS909/MS919/Ultra. 38+ special functions such as EPB/SAS/BMS/Oil/ABS/TPMS/Throttle/Injector/Suspension, etc., fix almost all “check engine” light issues. Bi-directional control, guided function, component matching, and scan VIN/license, together offer you effective and convenient diagnostic experiences.
- 🥇【DOIP& CAN FD Protocol, Top Hardware 5X Lightning Speed】Exclusive J2534 brings same DoIP & CAN FD protocol as Ultra/ MS919: CAN FD for GM MY2020+ Models; DOIP for BMW E/F/G Chassis, Jaguar, Land Rover makes. The improved hardware makes ELITE II PRO run more smoothly, even faster than MS919. It’s build with 8-Core CPU, Android 10.0 OS, 9.7’’ 1536*2048 touchscreen, 4GB&128GB, 11,000mAh battery, 2.4&5GHz dual-band WIFI, surpass Elite II/ Elite/ MS908S Pro II/ MK908 Pro II.
- 🔥【Free MV108 Assist Repairs】The MV108 digital inspection camera is designed to work with the MaxiSys series and PC, turning your MaxiSys scanner into a video inspection scope, allowing you to examine difficult-to-reach areas normally hidden from sight. It is capable of recording digital still images and videos, which offers you an economical solution to inspect machinery, facilities, and infrastructure quickly. One programmer tool Elite II Pro and one Videoscope MV108 make a perfect match.
- 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
- 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
- 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
- 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- Stay up-to-date with thelatest firmware and support of the SM2Pro J2534VCI ECUs programmer, ensuring reliable perform and optimalresults.
- The SM2Pro J2534VCI ECUs programmer is a trustedtool for professional technicians, offering comprehensive functionality and easy integration into your workflows.
- The SM2Pro J2534VCI ECUs programmer offersadvanced functionality for efficient and precise ECUs programming.
- With its 67IN1 without dongle & OBDcompatibility, the SM2Pro J2534VCI ECUs programmer provides a versatilesolution for read and write operations.
- Experienceseamless ECUs programming with the SM2Pro J2534VCI, designed to streamlines the read and write processes for enhanced efficiency.
- Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
- Supports Current & Earlier Vehicles: Enables diagnostics, programming and other “dealer” functions through OEM applications
- NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
- Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
- Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
DPS6 – NO START AND/OR TRANSMISSION ENGAGEMENT LOSS OF POWER WITH DTCS U0100, U0101, U1013 AND/OR P0606 Publication Date: September 26, 2016
OPERATION DESCRIPTION TIME 160129A 2011-2016 Fiesta, 2012-2016 Focus Automatic Transmission (DPS6): Retrieve DTCs, Reprogram The PCM/TCM And Perform The Clutch Adaptive Learning (Do Not Use With Any Other Labor Operations) 0.6 Hr. 160129B 2011-2016 Fiesta With Automatic Transmission (DPS6): Retrieve DTCs, Replace The TCM, Reprogram The PCM/TCM, Perform The Clutch Adaptive Learning Procedure And Clear DTCs (Closes FSA 15B22 If Open, Do Not Use With Any Other Labor Operation) 1.1 Hrs. 160129C 2012-2016 Focus With Automatic Transmission (DPS6): Retrieve DTCs, Replace The TCM, Reprogram The PCM/TCM, Perform The Clutch Adaptive Learning Procedure And Clear DTCs (Closes FSA 15B22 If Open, Do Not Use With Any Other Labor Operation) 1.0 Hr. WARRANTY STATUS Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage. Warranty/ESP coverage limits/policies/prior approvals are not altered by a TSB. Warranty/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool. DEALER CODING BASIC PART NO. CONDITION CODE 7Z369 04
**************************************************************************************************************
SEOCONTENT-END
compre un ford focus en estados unidos y estoy en republica dominicana aqui el dealer autorizado es Grupo Viamar me refieren que no me cubre en mi pais la garantia y tengo mi vehiculo parado puesto que le sucede exactamente lo descrito en este tutotorial no se que hacer por estoy desesperado
I have been having issues with my 2014 Ford Focus which was purchased from a Dealer in Jamaica. The vehicle has been jerking/bucking, running back while on a slope, overheating, losing power among other problems. I have had to take the vehicle in for repairs 3 times in the space of one week and it is still stuttering.
Kindly let me know who I should contact regarding this matter as I am extremely frustrated and disappointed with the service from Kingston Industrial Garage.
Thank you.
I’m afraid you will have to find another shop or dealer.