Climate Controlled Seat does not get Hot or Warm up Quickly – 2015 Lincoln MKC

FRONT CLIMATE CONTROLLED SEATS DO NOT GET HOT OR WARM UP QUICKLY – BUILT ON OR BEFORE 2/20/2015

 

LINCOLN:

2015 MKC

 

2015 Lincoln MKC vehicles built on or before 2/20/2015 may exhibit a climate controlled seat which does not get hot or warm up quickly.

 

SERVICE PROCEDURE

1. Using the Ford Integrated Diagnostic Service (IDS) or equivalent Scan Tool, perform a network test. Do the front seat climate control module (SCME) and front display interface module (FDIM) pass a network test?
   1. Yes – proceed to Step 2.
   2. No – this article does not apply. Refer to Workshop Manual (WSM), Section 501-10.
2. Perform a self-test of the SCME. Are any diagnostic trouble codes (DTCs) present?
   1. Yes – this article does not apply. Refer to WSM, Section 501-10.
   2. No – proceed to Step 3.
3. Is the vehicle built on or before 1/21/2015?
   1. Yes – proceed to Step 5.
   2. No – proceed to Step 4.
4. Is the vehicle built on 1/22/2015 and through 2/20/2015?
   1. Yes – proceed to Step 6.
   2. No – this article does not apply. Refer to WSM, Section 501-10 for normal diagnosis.
5. Make sure the IDS service tool has been updated to IDS release 94.03 or higher. Select Module Programming within the toolbox menu.
   1. Under Module Programming, select the Programmable Parameters menu.
      1. Do not attempt to use the As-Built function within the IDS programming menu. The configuration will fail to load completely due to the high number of modules found in the MKC.
   2. Black Label vehicles are identified by body type codes J1B or J3B in the 5th, 6th and 7th positions of the vehicle identification number (VIN).
      
      
      
      1. Enter the Programmable Parameters menu and select Climate Control Seats.
      
      
      
      2. Under Climate Control Seats, individually select each parameter on the left side, then click the appropriate vehicle level on the right for each selection. Click the blue check when completed. The asterisk should now move to the correct vehicle level at right, and each item at left should have the correct description according to the application selected. Once all three have been selected as shown in the chart below, click the blue check and follow on-screen prompts to completion. Proceed to Step 6.
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      
      

      Climate Control Seat Parameter Setting
      Parameter	Vehicle Level / Setting
      Lincoln Sales Badge	Black Label
      High Heat Final Set Point	76 Degrees Celsius	70 Degrees Celsius
      High Heat Initial Set Point	95 Degrees Celsius	95 Degrees Celsius
      VM – Initial Blower Set Point V	20.0 Volts	20.0 Volts

      
      

       

      
      
6. Remove the front seat backrest covers.
   1. If the vehicle has Black Label trim, it requires a unique front seat backrest cover removal procedure. Refer to the WSM, Section 501-10.
7. Remove and replace both front seat backrest foam pad and CCS bag assemblies.
8. Reinstall the front seat backrest covers.
9. Remove the front seat cushion covers.
10. Replace the front seat cushion foam pad and CCS bag assemblies.
11. Reinstall the front seat cushion covers.

 

GJ7Z-7864811-B	Driver Side Seat Back Pad (Base)
GJ7Z-7864810-B	Passenger Side Seat Back Pad (Base)
GJ7Z- 7864811-A	Driver Side Seat Back Pad (Black Label)
GJ7Z- 7864810-A	Passenger Side Seat Back Pad (Black Label)
GJ7Z-78632A23-A	Driver Seat Cushion Pad (Base)
GJ7Z-78632A22-A	Passenger Seat Cushion Pad (Base)
GJ7Z-78632A23-B	Driver Seat Cushion Pad (Black Label)
GJ7Z-78632A22-B	Passenger Seat Cushion Pad (Black Label)