Inoperative Park Aid Camera, Luggage Compartment Lamp, Luggage Compartment Lid Release And/Or Poor Satellite Radio Reception – 2015-2017 Ford Mustang

TECHNICAL SERVICE BULLETIN
Inoperative Park Aid Camera, Luggage Compartment Lamp, Luggage Compartment Lid Release And/Or Poor Satellite Radio Reception
18-2362
17 December 2018

 

Model:

Ford

2015-2017 Mustang

Issue: Some 2015-2017 Mustang vehicles may experience an inoperative rear parking aid camera, luggage compartment lamp, luggage compartment lid release and/or poor satellite radio reception. This may be due to damage to the 14A005 harness in the area of the right side luggage compartment lid hinge. This concern may be accompanied by diagnostic trouble codes (DTCs) B115E, C1001, and B1A89.

 

Action: Follow the Service Procedure steps to correct the condition.

 

Parts

Description Part Number Quantity
Wiring Harness (Coupe) FR3Z-14A411-X 1
Wiring Harness (Convertible) FR3Z-14A411-Y 1
Coroplast Electrical Wire Harness Tape NAI837X 1

Warranty Status: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage Warranty/ESP coverage limits/policies/prior approvals are not altered by a TSB. Warranty/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool.

 

Labor Times

Description Operation No. Time
2015-2017 Mustang Coupe: Retrieve DTCs, Inspect And Repair Wire Harness Following The Service Procedure (Do Not Use With Any Other Labor Operations) 182362A 1.2 Hrs.
2015-2017 Mustang Convertible: Retrieve DTCs, Inspect And Repair Wire Harness Following The Service Procedure (Do Not Use With Any Other Labor Operations) 182362B 2.8 Hrs.

 

Repair/Claim Coding

Causal Part: 14A005
Condition Code: 30

 

Tool List

Drive Tool Name
1/4″ Power Tool
1/4″ Ratchet
1/4″ Torque Wrench
1/4″ 2″ Extension
1/4″ 7 mm Socket
1/4″ 8 mm Socket
1/4″ 10 mm Socket
1/4″ 13 mm Socket
1/4″ Torx® T20
1/4″ Torx® T40
3/8″ Power Tool
3/8″ Ratchet
3/8″ Torque Wrench
3/8″ 15 mm Swivel Socket
Trim Tool
Solder Gun
Wire Strippers
Diagonal Cutting Pliers

 

Service Procedure

1. Does the vehicle exhibit an inoperative rear parking aid camera, luggage compartment lamp, luggage compartment lid release and/or poor satellite radio reception?

(1). Yes – proceed to Step 3.

(2). No – proceed to Step 2.

2. Using the appropriate Ford diagnostic scan tool or equivalent, retrieve DTCs. Is B115E, C1001, or B1A89 stored in the vehicle?

(1). Yes – proceed to Step 3.

(2). No – this article does not apply. Refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics.

3. Inspect the wiring harness on the underside of the luggage compartment lid. Is there evidence of wiring damage or chafing?

(1). Yes – proceed to the appropriate coupe or convertible procedure.

(2). No – this article does not apply. Refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics.

 

Coupe

1. Cut out the damaged section of the harness. Make the cut at the location of the harness noted. (Figure 1)

Figure 1

damaged section of the harness

2. Splice in the new section of harness, matching wire colors on the existing vehicle harness and the replacement section of harness as necessary. Follow the recommended wiring splice procedures in Section 5 of the Wiring Diagram. Stagger the location of each of the wire splices along the harness to minimize the overall size of the repair.

3. Wrap the spliced area in Coroplast Electrical Wire Harness Tape or equivalent.

4. Secure the replacement section of harness into the same body holes as the original section of harness was using the clips attached to the replacement section of harness.

5. If DTCs were previously present, connect the appropriate Ford scan tool or equivalent to the DLC and clear all DTCs.

 

Convertible

1. Cut out the damaged section of the harness. Make the cut at the location of the harness noted. (Figure 2)

Figure 2

damaged section of the harness

2. Splice in the new section of harness, matching wire colors on the existing vehicle harness and the replacement section of harness as necessary. Follow the recommended wiring splice procedures in Section 5 of the Wiring Diagram. Stagger the location of each of the wire splices along the harness to minimize the overall size of the repair.

(1). Note: While it is necessary to cut and remove a section of the old satellite radio antenna cable along with the rest of the harness, it is not necessary to splice the satellite radio antenna cable where the harness is cut. The satellite radio antenna cable provided with the new harness is long enough to overlay the entire length of the old cable.

3. Remove the existing ground on this section of the harness from the body of the vehicle. Reinstall the ground on the new section of harness to the body of the vehicle.

4. Overlay the satellite radio antenna cable included with the new section of harness. Refer to WSM, Section 415-00B, Satellite Radio Antenna, Removal and Installation.

5. Wrap the spliced area in Coroplast Electrical Wire Harness Tape or equivalent.

6. Secure the replacement section of harness into the same body holes as the original section of harness using the clips attached to the replacement section of harness.

7. If DTCs were previously present, clear all DTCs with the appropriate Ford diagnostic scan tool or equivalent.


18-2362
17 December 2018

https://www.nhtsa.gov/recalls?nhtsaId=10153932

https://static.nhtsa.gov/odi/tsbs/2018/MC-10153932-9999.pdf

Download (PDF, 259KB)


 

Bestseller No. 1
Bestseller No. 2
Bestseller No. 3
Bestseller No. 4
Bestseller No. 5
Bestseller No. 6
Tesa's Most Advanced High Heat Harness Tape 51036 Mercedes, BMW, Audi, VW
  • The most advanced high heat harness tape available
  • Rated to 150C, Superior abrasion resistance
  • Resists chemicals and fluids
  • AAA adhesive, self extinguishing
Bestseller No. 7
Boxiti set of 6 pcs Tesa 51608 Black Fuzzy Fleece Interior Wire Loom Harness Tape 19 mm X 15 Meters
  • Noise dampening
  • Abrasion resistant, tear resistant, age-resistant
  • Flexible and smooth
  • Stable unwind force, strong adhesion
  • Hand-tearable
Bestseller No. 8
Tesa Wire Loom Harness Tape Used By Mercedes BMW VW Audi
  • Big 19mm X 25m roll
  • Matches other wire looms in your car
  • Genuine German Quality
  • Good adhesion
  • Gives professional appearance
Bestseller No. 9
Adecco LLC 2 Rolls Wire Loom Harness Tape, Wiring Harness Cloth Tape, Adhesive Fabric Tape for Automobile 15m/19mm
  • Material:These wiring harness tape are made of high quality cotton flannel and strong adhesive glue.
  • Features: Strong adhesive force loom tape, no harmful substance, reduce noise, strong anti-aging, strong surface resistance and high stability at high temperature.
  • Size: Length 15 m. Width 19 mm. Package includes 2 rolls cloth tape.
  • Application: Suitable for the use of internal wiring harness of automobiles and can reduce the noise. Such as the wire harness of the dashboard.
  • QUALITY GUARANTEED: 30-day Products Exchange and Money Back Guarantee. If you have any problem,please feel free to contact us!
SaleBestseller No. 10
Automotive Wiring Harness Cloth Tape - Maxwel VERSAF51217 Chemical Fiber Cloth High Temp Wire Harness Wrapping Tape for Auto Electrical Wrap, Protection, Insulation 19MM × 25M Pack of 1 Piece
  • Wire looms in AUTO,19MM X 25M automotive wiring harness tape is widely used in automobiles;
  • High adhesive force,more than 1.5 N/cm adhesion to the backing for the harness tape;
  • High temperature resistance,-40℉-257℉ is available for applying this wire harness tape;
  • High abrasion resistance,engine harness tape provides excellent abrasion protection of wire harness;
  • ROHS & REACH Approved:high quality wiring loom harness tape with RoHs and REACH approved.

Last update on 2019-05-18 / Affiliate links / Images from Amazon Product Advertising API

Last update on 2019-05-18 / Affiliate links / Images from Amazon Product Advertising API

Leave A Comment

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.