| “This site contains affiliate links for which OEMDTC may be compensated” |
September 30, 2019 NHTSA CAMPAIGN NUMBER: 19V687000
Wiring Harness May Contact A/C Pulley or Belt
The A/C pulley may rub through the wiring harness insulation and contact the unfused battery positive wire, resulting in a short circuit, increasing the risk of a fire.
NHTSA Campaign Number: 19V687
Manufacturer Ford
Motor Company
Components ELECTRICAL SYSTEM
Potential Number of Units Affected 10,655
Summary
Ford Motor Company (Ford) is recalling certain 2020 Ford Explorer vehicles equipped with 2.3L or 3.3L engines. The wiring harness may not have been properly secured and may contact the air conditioner compressor (A/C) pulley, potentially damaging the harness or the A/C belt.
Remedy
Ford will notify owners, and dealers will install a tie strap to the wiring harness at the hand shock tower clip, free of charge. The recall began October 21, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford’s number for this recall is 19S32.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check if your Vehicle has a Recall
October 1, 2019
TO: All U.S. Ford and Lincoln Dealers
SUBJECT: NEW VEHICLE DEMONSTRATION / DELIVERY HOLD –
Safety Recall 19S32
Certain 2020 Model Year Explorer and Police Interceptor Utility Vehicles
with a 2.3L or 3.3L Gas Engine
Potential Wire Harness Contact to A/C Pulley
AFFECTED VEHICLES
| Vehicle | Model Year | Assembly Plant | Build Dates |
| Explorer | 2020 | Chicago | May 28, 2019 through July 18, 2019 |
| Police Interceptor Utility |
Affected vehicles are identified in OASIS and FSA VIN Lists.
REASON FOR THIS SAFETY RECALL
In some of the affected vehicles, the battery cable wire harness may not be properly secured at the right hand shock tower, allowing contact with the A/C compressor pulley. Over time, the A/C pulley may rub through the wire harness insulation and contact the unfused battery positive (B+) circuit, resulting in a short circuit and potential fire.
SERVICE ACTION
Before demonstrating or delivering any new in-stock vehicles involved in this recall, dealers are to inspect the battery cable wire harness for possible damage caused by contact with the A/C pulley, repair or replace the harness as necessary, and install a tie strap to prevent future contact. This service must be performed on all affected vehicles at no charge to the vehicle owner.
At this time, parts are not available to repair all vehicles. Until parts are available to repair all vehicles, dealers may submit a part order request to the SSSC to authorize repairs on customer-owned vehicles and unsold vehicles with a signed sales contact.
OWNER NOTIFICATION AND MAILING SCHEDULE
Owner letters are expected to be mailed the week of October 21, 2019. Dealers should repair any affected vehicles that arrive at their dealerships, whether or not the customer has received a letter.
PLEASE NOTE:
Federal law requires dealers to complete this recall service before a new vehicle is delivered to the buyer or lessee. Violation of this requirement by a dealer could result in a civil penalty of up to $21,000 per vehicle. Correct all vehicles in your new vehicle inventory before delivery.
ATTACHMENTS
Attachment I: Administrative Information
Attachment II: Labor Allowances and Parts Ordering Information
Attachment III: Technical Information
Owner Notification Letters
QUESTIONS & ASSISTANCE
For questions and assistance, contact the Special Service Support Center (SSSC) via the SSSC Web Contact Site. The SSSC Web Contact Site can be accessed through the Professional Technician Society (PTS) website using the SSSC link listed at the bottom of the OASIS VIN report screen or listed under the SSSC tab.
Sincerely,
David J. Johnson
ATTACHMENT I
NEW VEHICLE DEMONSTRATION / DELIVERY HOLD –
Safety Recall 19S32
Certain 2020 Model Year Explorer and Police Interceptor Utility Vehicles
with a 2.3L or 3.3L Gas Engine
Potential Wire Harness Contact to A/C Pulley
OASIS ACTIVATION
OASIS will be activated on October 1, 2019
FSA VIN LISTS ACTIVATION
FSA VIN Lists will be available through https://web.fsavinlists.dealerconnection.com on October 1, 2019. Owner names and addresses will be available by November 5, 2019.
NOTE: Your FSA VIN Lists may contain owner names and addresses obtained from motor vehicle registration records. The use of such motor vehicle registration data for any purpose other than in connection with this recall is a violation of law in several states, provinces, and countries. Accordingly, you must limit the use of this listing to the follow-up necessary to complete this recall.
SOLD VEHICLES
- Ford has not issued instructions to stop selling/delivering or driving used vehicles under this safety recall. Owners should contact their dealer for an appointment to have their vehicles remedied as soon as practicable. Owners can continue to safely drive their vehicles.
- Immediately contact any of your affected customers whose vehicles are not on your VIN list but are identified in OASIS. Give the customer a copy of the Owner Notification Letter (when available) and schedule a service date.
- Correct other affected vehicles identified in OASIS which are brought to your dealership.
- Dealers are to prioritize repairs of customer vehicles over repairs of new and used vehicle inventory.
STOCK VEHICLES
- Correct all affected units in your new vehicle inventory before delivery.
- Use OASIS to identify any affected vehicles in your used vehicle inventory.
DEALER-OPERATED RENTAL VEHICLES
The Fixing America’s Surface Transportation (FAST) Act law effective June 2016 prohibits a rental company from selling, renting or leasing vehicles subject to a safety or compliance recall. Please consult your legal counsel for legal advice.
TITLE BRANDED / SALVAGED VEHICLES
Affected title branded and salvaged vehicles are eligible for this recall.
OWNER REFUNDS
Refunds are not approved for this program.
RENTAL VEHICLES
For vehicles that DO NOT PASS the inspection and require wire harness replacement, dealers are pre-approved for up to two (2) days for a comparable rental vehicle. Follow Extended Service Plan (ESP) guidelines for dollar amounts. Rentals will only be reimbursed for the days the vehicle is at the dealership for part replacement. Prior approval for more than two (2) rental days is required from the SSSC. Contact the SSSC via the SSSC Web Contact Site for consideration and approval if appropriate.
ADDITIONAL REPAIR (LABOR TIME AND/OR PARTS)
Additional repairs identified as necessary to complete the FSA should be managed as follows:
- For related damage and access time requirements, refer to the Warranty and Policy Manual / Section 6 – Ford & Lincoln Program Policies / General Information & Special Circumstances for FSA’s / Related Damage.
- For vehicles within new vehicle bumper-to-bumper warranty coverage, no SSSC approval is required, although related damage must be on a separate repair line with the “Related Damage” radio button checked. o Ford vehicles – 3 years or 36,000 miles
- For vehicles outside new vehicle bumper-to-bumper warranty coverage, submit an Approval Request to the SSSC Web Contact Site prior to completing the repair.
CLAIMS PREPARATION AND SUBMISSION
- Claim Entry: Enter claims using Dealer Management System (DMS) or One Warranty Solution (OWS) online.
- When entering claims, select claim type 31: Field Service Action. The FSA number 19S32 is the sub code.
- For additional claims preparation and submission information, refer to the Recall and Customer Satisfaction Program (CSP) Repairs in the OWS User Guide.
- Related Damage/Additional labor and/or parts: Must be claimed as Related Damage on a separate repair line from the FSA with same claim type and sub code as described in Claim Entry above.
IMPORTANT: Click the Related Damage Indicator radio button.
- Rentals: For rental vehicle claiming, follow Extended Service Plan (ESP) guidelines for dollar amounts. Enter the total amount of the rental expense under Miscellaneous Expense code RENTAL.
- Provision for Locally Obtained Supplies: Includes parts such as wire terminals, splice kits, solder, tape and heat shrink tubing. Additional parts totaling more than $3.00 requires prior approval from the SSSC.
- Program Code: 19S32 o Expense: OTHER
- Amount: Actual cost up to $3.00
ATTACHMENT II
NEW VEHICLE DEMONSTRATION / DELIVERY HOLD –
Safety Recall 19S32
Certain 2020 Model Year Explorer and Police Interceptor Utility Vehicles
with a 2.3L or 3.3L Gas Engine
Potential Wire Harness Contact to A/C Pulley
LABOR ALLOWANCES
PASS Inspection
| Description | Labor Operation | Labor Time |
| 19S32A | 0.3 Hours |
DOES NOT PASS Inspection (only 2% of vehicles expected to not pass)
| Description | Labor Operation | Engine | Labor Time |
| Replace A/C compressor belt | 19S32B | 2.3L | 0.4 Hours |
| Replace A/C compressor belt | 19S32C | 3.3L | 0.6 Hours |
| Based on the inspection results, only one of the two labor operations BELOW should be used with DOES NOT PASS labor operations 19S32B OR 19S32C. | |||
| Description of Damage Found During Inspection | Labor Operation | Engine | Labor Time* |
REPAIR Harness – Repairable Damage Found
| MT19S32R
use with 19S32B OR 19S32C | All | Actual time up to
2.0 Hours |
REPLACE Harness – Non Repairable Damage Found
| MT19S32N use with
19S32B OR 19S32C | 2.3L | Actual time up to
3.0 Hours |
| 3.3L | Actual time up to
5.0 Hours | ||
*Labor time estimates are provided as a guide for each repair. If labor time exceeds the estimated labor time required to complete the repairs, submit an Approval Request to the SSSC Web Contact Site prior to submitting a claim.
PARTS REQUIREMENTS / ORDERING INFORMATION
SSSC Web Contact Site:
To place an order for parts, submit a VIN-specific Part Order contact via the SSSC Web Contact Site.
Required for all repairs:
| Description | Order Quantity | Claim Quantity | Part Number |
| Tie strap (high temperature rated) | 1 | 1 | LU5Z-14A163-B |
Optional parts may be required if inspection DOES NOT PASS:
| Description | Order Quantity | Claim Quantity | Part Number |
| A/C belt for 2.3L engine | 1 | 1 | L1MZ-8620-B |
| A/C belt for 3.3L engine | 1 | 1 | BR3Z-8620-S |
| Battery cable wire harness (refer to Ford Parts Catalog) | 1 | 1 | *-14300-* |
| Wire splice kit
(refer to Ford | Claim as
MISC OTHER | *-14A088-* | |
Dealers will be notified via a DOES II communication if circumstances warrant a change in part supply strategy and when open ordering resumes.
DEALER PRICE
For latest prices, refer to DOES II.
PARTS RETENTION AND RETURN
Follow the provisions of the Warranty and Policy Manual, Section 1 – WARRANTY PARTS RETENTION AND RETURN POLICIES.
EXCESS STOCK RETURN
Excess stock returned for credit must have been purchased from Ford Customer Service Division in accordance with Policy Procedure Bulletin 4000.
ATTACHMENT III
CERTAIN 2020 MODEL YEAR EXPLORER AND POLICE INTERCEPTOR UTILITY VEHICLES WITH A 2.3L OR 3.3L GAS ENGINE
OVERVIEW
In some of the affected vehicles, the battery cable wire harness may not be properly secured at the right hand shock tower, allowing contact with the A/C compressor pulley. Over time, the A/C pulley may rub through the wire harness insulation and contact the unfused battery positive (B+) circuit, resulting in a short circuit and potential fire.
Before demonstrating or delivering any new in-stock vehicles involved in this recall, dealers are to inspect the battery cable wire harness for possible damage caused by contact with the A/C pulley, repair or replace the harness as necessary, and install a tie strap to prevent future contact.
SERVICE PROCEDURE
1. Inspect the battery positive cable wire harness in the areas shown for damaged and exposed wire. See Figure 1.
– Replace the wire harness if any of the larger circuits (2/4/6 awg) have exposed copper wire strands.
– Repair any damaged (smaller gauge) circuits in the wire harness that have exposed copper wire strands. Please follow the recommended splicing method contained in the wire diagrams section of the Workshop Manual (WSM).
2. Inspect the tie-strap located on the passenger side strut tower. Tighten the tie-strap to properly retain the harness. See Figure 1.
– Replace the tie-strap if it cannot be tightened fully.
3. If damage to the battery positive cable wire harness was present, the Air Conditioning (A/C) compressor belt must be replaced. Please follow the WSM procedures in Section 303-05A for 2.3L engines or 303-05C for 3.3L engines.
4. Install a tie strap securing the battery positive cable wire harness to the engine wire harness.
See Figure 2.
March, 2020
* * * IMPORTANT SAFETY RECALL REMINDER * * *
According to our records, your 2020 Explorer has not had necessary safety recall repairs made. We urge you to have the free repair performed at your local dealership as soon as possible.
| Recall Number and Description: | 19S32 – POTENTIAL WIRE HARNESS CONTACT TO A/C PULLEY |
| What is the Issue? | On your vehicle, the battery cable wire harness may not be properly secured at the right hand shock tower, allowing contact with the A/C compressor pulley.
Over time, the A/C pulley may rub through the wire harness insulation and contact the unfused battery positive (B+) circuit, resulting in a short circuit and potential fire. |
If you have questions or concerns, please contact our Ford Customer Relationship Center at 1-866-436-7332.
If you wish to contact us through the Internet, our address is: www,Fordowner.com.
Thank you for your attention to this very important matter.
October 2019
* * * IMPORTANT SAFETY RECALL * * *
Safety Recall Notice 19S32 / NHTSA Recall 19V-687
2020 Explorer
Your Vehicle Identification Number (VIN):
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Ford Motor Company has decided that a defect which relates to motor vehicle safety exists in your vehicle, with the VIN shown above.
We apologize for this situation and want to assure you that, with your assistance, we will correct this condition. Our commitment, together with your dealer, is to provide you with the highest level of service and support.
| What is the issue? | On your vehicle, the battery cable wire harness may not be properly secured at the right hand shock tower, allowing contact with the A/C compressor pulley. |
| What is the risk? | Over time, the A/C pulley may rub through the wire harness insulation and contact the unfused battery positive (B+) circuit, resulting in a short circuit and potential fire. |
| What will Ford and your dealer do? | Ford Motor Company has authorized your dealer to install a tie strap to the battery cable wire harness to prevent future contact with the A/C compressor pulley. Your dealer will also inspect the battery cable wire harness for possible damage caused by contact with the A/C pulley and repair or replace the harness as necessary. These repairs will be free of charge (parts and labor). |
| How long will it take? | The time needed for this repair is less than one-half day. However, due to service scheduling requirements, your dealer may need your vehicle for a longer period of time. Additional time may be required to allow the engine to cool prior to performing this repair. In addition, your vehicle will require an inspection to determine if parts need to be ordered for an additional repair. |
| What should you do? | Please call your dealer without delay and request a service date for Recall 19S32. Provide the dealer with your VIN, which is printed near your name at the beginning of this letter.
Ford If you do not already have a servicing dealer, you can access www.Fordowner.com for dealer addresses, maps, and driving instructions. Ford Please note: Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days. NOTE: You can receive information about Recalls and Customer Satisfaction Programs through our FordPass App. The app can be downloaded through the App Store or Google Play. In addition there are other features such as reserving and paying for parking in certain locations and controlling certain functions on your vehicle (lock or unlock doors, remote start) if it is equipped to allow control. |
| Do you need a rental vehicle? | If your dealer determines that wire harness replacement is required and needs your vehicle overnight, your dealer is authorized to provide a rental vehicle for your personal transportation at no charge (except for fuel and insurance) while your vehicle is at the dealership for repairs. Please see your dealer for guidelines and limitations. |
| What if you no longer own this vehicle? | If you no longer own this vehicle, and have an address for the current owner, please forward this letter to the new owner.
You received this notice because government regulations require that notification be sent to the last known owner of record. Our records are based primarily on state registration and title data, which indicate that you are the current owner. |
| Can we assist you further? | If you have difficulties getting your vehicle repaired promptly and without charge, please contact your dealership’s Service Manager for assistance.
RETAIL OWNERS: If you have questions or concerns, please contact our Ford For the hearing impaired call 1-800-232-5952 (TDD). Representatives are available Monday through Friday: 8:00AM – 8:00PM (Eastern Time). FLEET OWNERS: If you have questions or concerns, please contact our Fleet Customer Information Center at 1-800-34-FLEET, choose Option #3, and one of our representatives will be happy to assist you. If you wish to contact us through the Internet, our address is: www.fleet.ford.com. Representatives are available Monday through Friday: 8:00AM – 8:00PM (Eastern Time). If you are still having difficulty getting your vehicle repaired in a reasonable time or without charge, you may write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave. S.E., Washington, D.C. 20590 or call the toll free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153) or go to www.safercar.gov. Reference NHTSA Safety Recall 19V-687. |
Thank you for your attention to this important matter.
Ford Customer Service Division
Octubre de 2019
* * * CAMPAÑA DE SEGURIDAD IMPORTANTE * * *
Aviso de campaña de seguridad 19S32 / Campaña 19V-687 de la NHTSA
2020 Explorer
Número de identificación del vehículo (VIN):
Este aviso se le envía de acuerdo con la Ley Nacional de Seguridad y Tránsito de Vehículos de los EE. UU. Ford Motor Company ha determinado que su vehículo presenta un defecto relacionado con la seguridad del motor, con el VIN que aparece más arriba.
Lamentamos esta situación y deseamos asegurarle que, con su ayuda, corregiremos el problema.
| ¿Cuál es el problema? | En su vehículo, el arnés de la batería podría no estar correctamente asegurado en la torre del amortiguador del lado derecho, lo cual hace posible el contacto con la polea del compresor del A/C. |
| ¿Qué riesgo existe? | Con el paso del tiempo, la polea del A/C podría rozar en el aislamiento del arnés y generar contacto con el circuito positivo de la batería (B+) sin fusible, lo cual se traduce en un cortocircuito y un posible incendio. |
| ¿Qué medidas adoptarán Ford y su distribuidor? | Ford Motor Company ha autorizado a su distribuidor a instalar una cinta de amarre al arnés de la batería a fin de evitar contacto futuro con la polea del compresor de A/C. Su distribuidor también inspeccionará el arnés de la batería para detectar posibles daños causados por el contacto con la polea del A/C y reparar o reemplazar el arnés, según sea necesario. Estas reparaciones se realizarán sin costo alguno (piezas y mano de obra). |
| ¿Cuánto tiempo tomará? | El tiempo necesario para reparar será menos de medio día. Sin embargo, debido a los requisitos de planificación de servicio, es posible que su distribuidor tarde un poco más. Es posible que se necesite más tiempo para permitir que el motor se enfríe antes de realizar esta reparación. Además, su vehículo requerirá una inspección para determinar si se deben solicitar piezas para llevar a cabo una reparación adicional. |
| ¿Qué debe hacer? | Llame a su distribuidor lo antes posible y solicite una cita de servicio para llevar a cabo la campaña 19S32. Proporcione el VIN a su distribuidor, el cual está impreso debajo de sus datos al comienzo de esta carta.
Para esta campaña de seguridad, Ford Puede continuar manejando su vehículo con seguridad. Si aún no tiene un distribuidor para realizar el servicio, puede acceder a www.Fordowner.com para conocer las direcciones de los distribuidores, ver mapas y obtener las instrucciones para llegar. Ford Tenga presente que: la ley federal exige que los arrendadores de vehículos que reciban este aviso de campaña envíen una copia del mismo al arrendatario en un plazo de diez días. NOTA: puede recibir información sobre las campañas y los programas de satisfacción del cliente a través de la aplicación FordPass. La aplicación se puede descargar a través de App Store o Google Play. Adicionalmente, existen otras funciones, como reserva y pago de estacionamientos en ciertos lugares, además de control de ciertas funciones en el vehículo (bloqueo y desbloqueo de puertas, arranque remoto) si así está equipado para permitir el control. |
| ¿Necesita un vehículo de alquiler? | Si su distribuidor determina que es necesario efectuar el reemplazo del arnés y el vehículo debe permanecer en las instalaciones durante la noche, el distribuidor está autorizado a ofrecerle un vehículo de alquiler para su transporte personal sin costo (excepto combustible y seguro) mientras su vehículo se encuentre en reparación. Comuníquese con su distribuidor para conocer las pautas y limitaciones. |
| ¿Qué pasa si usted ya no es el propietario del vehículo? | Si usted ya no es el propietario del vehículo y tiene la dirección del propietario actual, le solicitamos que le reenvíe esta carta.
Usted recibió este aviso porque las regulaciones del gobierno exigen el envío de notificaciones al propietario conocido más reciente del registro. Nuestros registros se basan principalmente en datos estatales y de propiedad, que indican que usted es el propietario actual del vehículo. |
| ¿Podemos hacer algo más por usted? | Si tiene problemas para reparar de inmediato su vehículo y sin costo alguno, comuníquese con el Gerente de Servicio de su distribuidor para solicitar ayuda. PROPIETARIOS MINORISTAS: si tiene dudas o preguntas, comuníquese con nuestro Centro de Relación con Clientes Ford al 1-866-436-7332 y uno de nuestros representantes con gusto lo atenderá. Si desea comunicarse con nosotros a través de Internet, nuestra dirección es: www.Fordowner.com. Las personas con problemas de audición pueden llamar al 1-800-232-5952 (TDD). Los representantes atienden de lunes a viernes, 8:00 am a 8:00 pm (hora local).
PROPIETARIOS DE FLOTAS: si tiene dudas o preguntas, comuníquese con nuestro Centro de Información a Clientes de flotas al 1-800-34-FLEET, elija la opción n.° 3 y uno de nuestros representantes con gusto lo atenderá. Si desea comunicarse con nosotros a través de Internet, nuestra dirección es: www.fleet.ford.com. Los representantes atienden de lunes a viernes, 8:00 am a 8:00 pm (hora local). Si continúa con dificultades para reparar su vehículo en un tiempo razonable o sin cargo, le sugerimos que escriba al Administrador, National Highway Traffic Safety Administration, 1200 New Jersey Ave. S.E., Washington, D.C. 20590 o bien que llame sin cargo a la línea directa de seguridad vehicular al 1-888-327-4236 (TTY: 1-800-424-9153) o visite www.safercar.gov. Mencione la Campaña de seguridad 19V-687 de la NHTSA. |
Gracias por su atención en este asunto sumamente importante.
Ford, División de Servicio al Cliente
Ford Media Center
FORD MOTOR COMPANY ISSUES TWO SAFETY RECALLS, AMENDS A PREVIOUS RECALL
OCT 2, 2019 | DEARBORN, MICH.
DEARBORN, Mich., Oct. 2, 2019 – Ford Motor Company is issuing two safety recalls in North America and amending safety compliance recall 19C07. Details are as follows:
Safety recall for select 2019 Ford F-Series Super Duty vehicles
Ford is issuing a safety recall for select 2019 Ford F-Series Super Duty vehicles. On affected vehicles, the electronically locking rear-axle assembly may have a passenger-side axle shaft manufactured with steel that does not meet Ford’s specifications. A passenger-side rear axle shaft manufactured with material not to Ford’s specifications may fracture. A fractured passenger-side axle shaft could result in a loss of motive power while driving in two-wheel drive, and the inability to hold the park function. If the parking brake is not applied, this could result in unintended vehicle movement, increasing the risk of crash or injury.
Ford is not aware of any reports of accident or injury related to this condition.
This action affects 28,579 vehicles in the United States and federal territories, 4,316 in Canada and 73 in Mexico.
Affected vehicles were built at Kentucky Truck Plant and Ohio Assembly Plant, May 21 – July 26, 2019.
Dealers will inspect the passenger-side rear axle shaft; shafts with a suspect batch code will be replaced. Owners are advised to apply the parking brake whenever the vehicle is parked until the service fix is completed. The Ford reference number for this recall is 19S31.
Safety recall for select 2020 Ford Explorer vehicles for an improperly secured wiring harness
Ford is issuing a safety recall for select 2020 Ford Explorer vehicles with 2.3-liter and 3.3-liter gas engines. In affected vehicles, the wiring harness is not properly secured and may contact the air-conditioning pulley, resulting in a damaged wiring harness or damaged air-conditioning drive belt. Over time, contact with the air-conditioning pulley may rub through the wiring harness insulation, creating the potential for contact with the unfused B+ circuit, resulting in a short circuit and possible fire.
Ford is not aware of any reports of accidents, injuries or fires related to this condition.
This action affects 10,655 vehicles in the United States. The majority of affected vehicles are in dealer inventory. The issue will be remedied prior to delivery to customers.
Affected vehicles were built at Chicago Assembly Plant, May 28 – July 18, 2019.
Dealers will secure the wiring harness and repair any damage, if present. The Ford reference number for this recall is 19S32.
Safety compliance recall 19C07 amended to include select 2020 Ford Escape vehicles
Ford is issuing an amendment to safety compliance recall 19C07 announced Aug. 30, 2019, to include select 2020 Ford Escape vehicles and expand the build date range of other affected vehicles. The amendment includes approximately 9,350 Escape vehicles in North America built April 3, 2019, to Sept. 21, 2019 at Louisville Assembly Plant. The majority of vehicles are in dealer inventory and this issue will be remedied prior to customer delivery”
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
| FORD | EXPLORER | 2020 |
9 Associated Documents
ISSUED Owner Notification Letter(Part 577)
RCONL-19V687-6760.pdf 94.167KB
Loading...
Reload document 
Open in new tab
Recall Quarterly Report #1, 2019-4
RCLQRT-19V687-1145.PDF 211.145KB
Loading...
Recall Quarterly Report #2, 2020-1
RCLQRT-19V687-5541.PDF 211.247KB
Loading...
ISSUED Renotification Notice
RCRN-19V687-3300.pdf 1348.788KB
Loading...
Manufacturer Notices(to Dealers,etc)- NEW VEHICLE DEMONSTRATION / DELIVERY HOLD – Safety Recall 19S32
RCMN-19V687-8679.pdf 570.957KB
Loading...
Miscellaneous Document – Ford Media Center
RMISC-19V687-9832.pdf 293.843KB
Loading...
Recall Acknowledgement
RCAK-19V687-5530.pdf 244.841KB
Loading...
Defect Notice 573 Report
RCLRPT-19V687-7105.PDF 214.039KB
Loading...
Recall Quarterly Report #3, 2020-2
RCLQRT-19V687-2181.PDF 211.332KB
Loading...
Latest Recalls Documents
- High temp Wire Harness Automotive Cloth Tape with excellent sound and rattle dampening performance. Lessens coil whining and lasts well against elevated temperatures (-40℉ - 257℉).
- Sports a race-spec heavy-duty bundling performance but cleanly tears with just bare hands, EMPOWERING average car owners with LITTLE TO NO EXPERIENCE in automotive maintenance to achieve PROFESSIONAL-GRADE results in function and form.
- This Wire Loom Tape features an extremely strong adhesive but does not turn into a messy goo. Rated to last up to 6 years and can easily get you through 150k miles of mileage.
- Its bi-directional weave makes it puncture-resistant and abrasion and corrosion-resistant. This automotive felt tape preserves cables in their pristine condition.
- This engine tape wrap is similar, if not better, in thickness, tensile strength and looks with OEM wire harness tapes. Extra-sticky adhesive enables users to bundle hard-to-reach cables quickly.
- Widely application: The material of wire harness cloth tape is soft and corrosion-resistant, which is suitable for the use of wire harness in automobile interior noise reduction part, such as wire harness of the dashboard, main harness wound and applied for wire joint and wire fixing; It can also sort out home appliance wiring and more
- Easy to tear: Just stick one end of tape to cable, start pulling and wrapping onto the cable and tear it gently; No need scissors and other tools; You can decide the length of the wire cloth tape according to you needs
- Professional cloth tape material: It is made of polyester non-woven fabric and strong acrylic pressure sensitive adhesive; High viscosity, high temperature resistance ( -40°F to 221°F ), well seal and excellent flexibility
- Excellent performance: The wiring harness tape maintains features high adhesive force, good noise reduction, hand tearable and heat insulation performance, and wear resistance; It is suitable for electrical automotive engine and circuit maintenance to achieve the purpose of insulation protection
- Specification: A set of 5 rolls wire harness cloth tap; SIZE: Each roll black electrical harness tape is 50 FT long and 3/4 inch wide; It is work for your different daily needs in diversified use scenarios
- Harness Cloth Tape Application: Suitable for the use of internal wiring harness of automobiles and can reduce the noise. Such as the wire harness of the dashboard.
- Harness Cloth Tape Material: These wiring harness tape are made of high quality cotton flannel and strong adhesive glue.
- Harness Cloth Tape Features: 1High Adhesive Force 2 Noise Resistance Well 3 Strong Abrasion Resistance 4 Hand Tearable 5 Strong Chemical Resistance.
- Harness Cloth Tape Size: Length 15 m, Width 15 mm.
- Car harness cloth tape is very convenient to use; just wrap the tape around the wire and gently tear it apart. No scissors or other tools are needed. The length of the tape can be determined according to your needs.
- Enough to Use: you will get 2 rolls of wire harness tapes in the package, measuring approx. 2 inches x 49.2 ft/ 50 mm x 15 m for each; The proper size and sufficient length is suitable for your different daily needs in many use scenarios
- Safe Material: the wire harness tape is made of polyester non woven fabric material, quality pressure sensitive adhesive, high temperature and wear resistance, which can be applied for a long time
- Nice Performance: the adhesive fabric tape has nice noise reduction and heat insulation performance, very suitable for automotive engine and circuit maintenance to achieve the purpose of insulation protection
- Easy to Use: the wire loom tape is simple and convenient to use, just wrap the tape on the wire and tear it gently, and you can decide the length of the tape according to your own needs
- Scope of Usage: the cloth electrical tape is suitable for automobile interior noise reduction part, such as instrument panel harness and main harness wound, and can also be applied for wire joint and wire fixing
- Speaker wire harness tape dimensions: 2 Rolls, Length 50ft，Width 15mm.
- Wire Harness Tape Material: These wire harness tapes are made of high quality cotton flannel and strong adhesive.
- Features of loom wire harness tape: strong loom tape, no harmful substances, reduced noise, strong anti-aging ability, strong surface resistance, high high temperature stability. Pressure-sensitive acrylic adhesive that is flame retardant to temperatures up to 225°F (107°C) and remains extremely flexible even below freezing.
- Wiring harness tape application: Suitable for the use of wiring harnesses inside cars to reduce noise. For example, the wiring harness for the instrument panel.
- Car wiring harness tape is very easy to use: just wrap the tape around the wires and gently peel it off. No scissors or other tools required. The length of the tape can be determined according to your needs.
- High Temp Wire Harness Tape: Withstands -40℉ to 250℉, providing soundproofing and vibration dampening.
- OEM-Grade Adhesion: Meets or exceeds OEM standards with strong adhesive for easy cable bundling.
- Easy to Use: Tear by hand—no scissors needed. Flexible for quick adjustments.
- Durable Protection: Resists punctures, abrasion, and corrosion to keep cables intact.
- Multi-Purpose: Ideal for automotive wiring, appliance cords, and household use.
- 1.【High-Temp Automotive Cloth Tape】 Wire Harness Tape offers exceptional sound and rattle dampening performance, reducing coil whining and enduring high temperatures ranging from -40°F to 257°F.
- 2.【Flame Retardant & Convenient & Reliability】Guarantee wires well insulating and protecting, Highly flexible, stretchy and conformable.
- 3.【Heavy-Duty Bundling Tape】Made from durable polyester fabric with a bi-directional weave finish, this tape tears cleanly by hand. It enables novice car owners to achieve race-spec bundling results effortlessly.
- 4.【Long-Lasting Wire Loom Tape】Engineered with a robust adhesive, this tape stays clean, offering 6-year longevity and safeguarding over 150k miles of mileage.
- 5.【Puncture-Resistant Wire Loom Tape】: With a bi-directional weave, this tape is resistant to punctures, abrasions, and corrosion, effectively preserving cables and keeping them in pristine condition.
- HIGHLY DURABLE: Designed for automotive wire protection, tesa 51036 PET cloth tape delivers superior abrasion protection and withstands high temperatures and demanding environmental conditions.
- SECURE CLOSURE: The solvent-free, advanced acrylic adhesive (triple A) is highly resistant to flagging and ensures a reliable closure.
- EASY TO USE: Can be used for both manual and automatic applications, this tape features a consistent unwind force and a flexible backing for a smooth application, ensuring an efficient installation process.
- APPLICATIONS: Specially designed for bundling and wire protection against abrasion in automotive engine compartments with demanding temperature-related and environmental conditions.
- SPECIFICATIONS: This tape measures 19 mm wide by 25 m long with a 10.2 mil thickness. It resists temperatures from -40 F to 302 F. Abrasion Resistance (5mm mandrel, LV312) Class D, Abrasion Resistance (10mm mandrel, LV312) Class D, Noise Damping (LV312) Class A.
- High Temp Durable Performance: Withstands temperatures from -40℉ to 257℉, making this wire harness tape ideal as an automotive tape for engine compartments. This cloth tape resists abrasion and corrosion.
- Noise Dampening Wire Loom Tape: Reduces coil whining and vibrations for quieter cabins, dashboards, and machinery. This cloth electrical tape provides heavy-duty bundling and insulation.
- Residue-Free: Our heat shrink tape features a strong adhesive that bonds securely without leaving a sticky residue. Rated to last up to 6 years, this wiring harness tape ensures reliable, mess-free performance.
- Flexible and Easy to Use Automotive Tape: This high temp tape tears cleanly by hand for quick application, ideal for DIYers and professionals. This fabric electrical tape is perfect for bundling and insulating household wires.
- Weatherproof and Flame Retardant: Our wire tape resists UV, moisture, and extreme temperatures for year-round protection in high-heat areas like engine compartments.
- Abrasion Resistance Material: This automotive wiring harness cloth tape is made of velvet material. The velvet material has good softness and elasticity, which enables the velvet harness tape to fit tightly to the surface of the harness, thus ensuring that the harness is fixed and stabilized. This tight fit not only helps reduce friction and wear, but also prevents the harness from loosening or being damaged by vibration or shock.
- Wide Compatibility: This automotive wiring harness fabric adhesive is suitable for the noise reduction part of the car interior, it is not only suitable for noise reduction in the engine compartment and passenger compartment and other specific areas of the car, but also suitable for organizing the wires wherever else they are needed, which can ensure safer electrical installations and repairs. Its suitable for electrical tape, automotive engine harness tape, battery winding insulation.
- DIY Design: This automotive wire harness fabric tape is easy to use. First, you should wrap the tape around the wires. Then, you just need to gently peel off the tape and stick it to the desired surface to complete the installation. There is no need for scissors or other tools during the application process, you just need to tear it by hand. Its flexibility allows the tape to be as long as you need it to be.
- Noise Reduction: This automotive wiring harness fabric adhesive has good soundproofing properties, which can reduce abnormal noise and thus improve the overall performance of your car. This automotive wiring harness fabric adhesive not only provides good sound insulation and vibration damping, but also effectively organizes and protects wires, thus creating a neater and more spacious interior for your vehicle.
- Package Include: Our product package comes with 2 rolls of wire harness tape, each measuring approximately 984.25 x 0.10 x 0.10 inches. This size design ensures the practicality of the tape, as well as portability and easy storage. The tape fits snugly when wrapped and will not loosen or fall off, thus ensuring good insulation and retention.
Last update on 2025-05-10 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.