2017 Ford Mustang

Safety Recall 22S06 – Luggage Compartment Lid Wiring Inspection and Rear View Camera Improper Function – 2015-2017 Ford Mustang

by
BufferCopyFlipboardHacker NewsLinkedInMessengerMixPinterestPrintRedditSMSTelegramTumblrVKWhatsAppLineXingThreads

February 16, 2022 NHTSA CAMPAIGN NUMBER: 22V082000

Blank or Distorted Rearview Camera Image

A rearview camera that displays a blank or distorted image can reduce the driver’s rear view, increasing the risk of a crash.

 

NHTSA Campaign Number: 22V082

Manufacturer FordeBay logo Motor Company

Components BACK OVER PREVENTION

Potential Number of Units Affected 330,784

 

Summary

FordeBay logo Motor Company (FordeBay logo) is recalling certain 2015-2017 MustangeBay logo vehicles. The rearview camera wiring may be loose or damaged, which can result in a blank or distorted image.

 

Remedy

Dealers will inspect and repair the decklid wiring harness and/or replace the rearview camera, as necessary, free of charge. Interim owner notification letters informing owners of the safety risk were mailed on October 21, 2022. Remedy parts are expected to become available in the 4th Quarter of 2022. Owner notification letters were mailed on December 23, 2022. Owners may contact FordeBay logo customer service at 1-866-436-7332. FordeBay logo’s number for this recall is 22S06.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

 

Check if your Vehicle has a Recall

 

December 14, 2022

NEW VEHICLE DEMONSTRATION / DELIVERY HOLD
Safety Recall 22S06 – Supplement #2
Certain 2015-2017 Model Year MustangeBay logo Vehicles
Luggage Compartment Lid Wiring Inspection and Rear View Camera Improper Function

 

AFFECTED VEHICLES

Vehicle Model Year Assembly Plant Build Dates
MustangeBay logo 2015-2017 Flat Rock February 11, 2014 through October 2, 2017

Affected vehicles are identified in OASIS and Field Service Action (FSA) VIN Lists.

 

REASON FOR THIS SAFETY RECALL

In all of the affected vehicles, damage to the luggage compartment lid wiring harness in the area of the right side luggage compartment lid hinge may lead to intermittent rear view camera operation, loss of satellite radio reception, inoperative luggage compartment lamp and/or inoperable luggage compartment release.

In addition, in some of the affected 2015 model year vehicles, insufficient electrical conductivity within the Printed Circuit Board (PCB) internal to the camera may also lead to intermittent rear view camera operation.

A rear view camera that intermittently displays a blank or distorted image can reduce the driver’s view of what is behind the vehicle increasing the risk of a crash.

 

SERVICE ACTION

  • 2015 Vehicles: Dealers are to check the vehicle build date and, if necessary, the rear view camera engineering part number. A review of the vehicle warranty and customer pay history is required to determine if Technical Service Bulletin (TSB) 18-2362 or 19-2273 was previously performed. As needed, dealers are to replace the rear view camera and/or modify the luggage compartment lid harness or install a luggage compartment lid wiring jumper harness per the technical instructions.
  • 2016-2017 Vehicles: Dealers are to review the vehicle warranty and customer pay history to determine if TSB 18-2362 or 19-2273 was previously performed. As needed, dealers are to modify the luggage compartment lid harness or install a luggage compartment lid wiring jumper harness per the technical instructions.

This service must be performed on all affected vehicles at no charge to the vehicle owner.

 

OWNER NOTIFICATION AND MAILING SCHEDULE

Owners of affected vehicles have been notified. For some 2015 model year vehicles requiring rear view camera replacement, parts available owner letters are expected to be mailed in the 2nd quarter of 2023. For all other vehicles, parts available owner letters are expected to be mailed the week of January 09, 2023. Dealers should repair any affected vehicles that arrive at their dealerships, whether or not the customer has received a letter.

PLEASE NOTE:

Federal law requires dealers to complete this recall service before a new vehicle is delivered to the buyer or lessee. Violation of this requirement by a dealer could result in a civil penalty of up to $21,000 per vehicle. Correct all vehicles in your new vehicle inventory before delivery.

 

SOLD VEHICLES

  • FordeBay logo has not issued instructions to stop selling/delivering or driving used vehicles under this safety recall. Owners should contact their dealer for an appointment to have their vehicles remedied as soon as practicable.
  • Immediately contact any of your affected customers whose vehicles are not on your VIN list but are identified in OASIS. Give the customer a copy of the Owner Notification Letter and schedule a service date.
  • Correct other affected vehicles identified in OASIS which are brought to your dealership.
  • Dealers are to prioritize repairs of customer vehicles over repairs of new and used vehicle inventory.

 

STOCK VEHICLES

  • Correct all affected units in your new vehicle inventory before delivery.
  • Use OASIS to identify any affected vehicles in your used vehicle inventory.

 

DEALER-OPERATED RENTAL VEHICLES

The Fixing America’s Surface Transportation (FAST) Act law effective June 2016 prohibits a rental company from selling, renting or leasing vehicles subject to a safety or compliance recall. Please consult your legal counsel for legal advice.

 

TITLE BRANDED / SALVAGED VEHICLES

Affected title branded and salvaged vehicles are eligible for this recall.

 

OWNER REFUNDS

  • This safety recall must still be performed, even if the owner has paid for a previous repair. Claiming a refund will not close the recall on the vehicle.
  • FordeBay logo Motor Company is offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which is posted with this bulletin. Owners are directed to seek reimbursement through authorized dealers or, at their option, directly through FordeBay logo Motor Company at P.O. Box 6251, Dearborn, MI 481216251.
  • Dealers are also pre-approved to refund owner-paid emergency repairs that were performed away from an authorized servicing dealer after the end date specified in the reimbursement plan. Non-covered repairs, or those judged by FordeBay logo to be excessive, will not be reimbursed.
  • Refunds will only be provided for the cost associated with rear view camera and/or luggage compartment lid wiring.

 

RENTAL VEHICLES

Dealers may receive approval for up to 1 day for a comparable rental vehicle if parts are required after inspection. Follow Extended Service Plan (ESP) guidelines for dollar amounts. Rentals will only be reimbursed for the day(s) the vehicle is at the dealership for part replacement. Prior approval is required from the SSSC. Contact the SSSC via the SSSC Web Contact Site for consideration and approval if appropriate.

 

PARTS REQUIREMENTS

Part Number Description Order Quantity
FR3Z-19G490-AeBay logo 2015 MustangeBay logo Only

Rear View Camera (All models)

 1

(If Required)
FR3Z-14A411-X Luggage Compartment Lid Jumper Harness (Coupe) 1

(If Required)
FR3Z-14A411-Y Luggage Compartment Lid Jumper Harness (Convertible)
GU5Z-00817-B    Tape on Push Pin Retainer (Coupe) 1 (If Required)
8U5Z-00817-ZA Tape on Push Pin Retainer (Convertible) 2 (If Required)
W505255-S450L Electrical Ground Bolt (Convertible)

– Only if a Luggage Compartment Lid Jumper Harness is Installed (As Needed)

 1 (If Required)
NU5Z-14A163-E Support Stick (Coupe/Convertible) 1 (If Required)
KU5Z-14A163-C Tie Strap Push Pin Retainer (Coupe/Convertible) 1 (If Required)
3U2Z-14A088-AB

No products found.

 Wiring Splice Kit (Coupe) 2  (If Required)
Wiring Splice Kit (Convertible) 3  (If Required)
Obtain Locally
(As Needed)		 Engineered Electrical Wire Harness Tape*

Coroplast® 837 or Equivalent

– Can Be Obtained From Rotunda or Nairn (NAI837X). Package of 3 or 6 Rolls.

 Claim as Misc. OTHER
(If Required)
Fleece Tape*

Tesa® 51608 PET Fleece or Equivalent
Electrical (PVC)Tape*

KTI73510 or Equivalent

– Can Be Obtained From Rotunda  Package of 10 Rolls.
Rosin Core Solder*

* The listed tapes and the rosin core solder can be used on multiple vehicles.

 

CERTAIN 2015-2017 MODEL YEAR MUSTANGeBay logo VEHICLES — LUGGAGE COMPARTMENT LID WIRING INSPECTION AND REAR VIEW CAMERA IMPROPER FUNCTION

SERVICE PROCEDURE

1. Is the vehicle a 2015 model year built between May 12, 2014 and February 28, 2015?

YES – Proceed to Step 2.

NO  – Proceed to Step 4.

2. Remove the Rear Parking Aid Camera. Please follow the Workshop Manual (WSM) procedures in Section 413-13B.

3. With the rear parking aid camera out of the vehicle, inspect the engineering part number on the back of the camera. See Figure 1.

– Is the part number FR3T-19G490-AH?

YES – Reinstall the Rear Parking Aid Camera. Please follow the WSM procedures in Section 413-13B. Do not install the luggage compartment lid trim at this time.  Proceed to Step 4.

NO  – Replace the Rear Parking Aid Camera. Please follow the WSM procedures in Section 413-13B. Do not install the luggage compartment lid trim at this time. Proceed to Step 4.

 

4. Review the vehicle warranty and customer pay history to determine if Technical Service Bulletin (TSB) 18-2362 or 19-2273 was previously performed.

– Has the luggage compartment lid wiring harness been previously repaired per TSB 18-2362 or 19-2273?

YES – Re-assemble the luggage compartment lid trim if previously removed. Safety recall is complete. If the rear parking  aid camera, satellite radio (if equipped), luggage compartment lamp and/or luggage compartment lid release is not operating correctly, pursue normal diagnostics upon customers request only.

NO –  Inspect the luggage compartment lid wiring.

For Coupe – 2015 Vehicles – Proceed to Step 8 (Page 4).
2016-2017 Vehicles – Proceed to Step 5.
For Convertible – 2015 Vehicles – Proceed to Step 42 (Page 19).
2016-2017 Vehicles – Proceed to Step 40 (Page 18).

 

Coupe

5. Remove the luggage compartment lid emergency release handle. See Figure 2.

 

6. Remove the luggage compartment lid latch cover. See Figure 3.

 

7. Remove luggage compartment lid trim panel. See Figure 4.

 

8. Disconnect the negative battery cable and position aside. Please follow the WSM procedures in Section 414-01.

NOTE: Do not cut or remove the mesh sleeve.

9. Disconnect the lower tie strap push pin retainer located inside the luggage compartment. See Figure 5.

 

10. Disconnect the wire harness tape on push pin retainer from the luggage compartment lid. See Figure 6.

 

11. Remove and discard the lower tie strap push pin retainer. See Figure 7.

 

12. Remove the tape and discard the wire harness tape on push pin retainer. See Figure 8.

 

NOTE: Do not cut or remove the mesh sleeve.

13. Remove the tape to expose both ends of the mesh sleeve. See Figure 9.

 

14. Position the mesh sleeve up out of the way. See Figure 10.

 

15. Remove and discard the felt tape to expose the wiring within the harness from the upper tie strap push pin retainer to the wiring harness take out. See Figure 11.

 

16. Remove and discard the tape and the plastic tube. See Figure 12.

 

NOTE: Do not damage the foil tape underneath the electrical tape as it will be reused further in the   procedure.

17. Locate the twisted wires. Carefully remove and discard the electrical tape on the twisted wires the full length of the exposed wiring. See Figure 13.

 

NOTE: Do not damage the foil tape as it will be reused further in the procedure.

18. Carefully unwrap the foil tape on the twisted wires the full length of the exposed wiring. See Figure 14.

 

19. Inspect the entire exposed portion of the wiring harness for any sign(s) of damage or chafing. See Figure 14.

– Is any damage or chafing found?

Yes – Proceed to Step 20.

No – Proceed to Coupe Harness – Repair Parts Needed (Page 11) then Step 26 (Page 12).

NOTE: One example of wiring damage, others similar.

 

20. Cut out the damaged section of the harness. Make the cut at the location of the harness noted. See Figure 16.

 

NOTE: Obtain two 3U2Z-14A088-AB wiring splice kits. Discard the butt splices and only use the heat shrink tubes for the repair.

21. Splice in the new section of harness, matching wire colors on the existing vehicle harness and the replacement section of harness as necessary. Follow the recommended wiring splice procedures in Section 5 of the Wiring Diagram using solder not wire crimps. Stagger the location of each of the wire splices along the harness to minimize the overall size of the repair.

22. Wrap the spliced area in Coroplast® 837 electrical wire harness tape or equivalent.

23. Secure the replacement section of harness into the same body holes as the original section of harness was using the clips attached to the replacement section of harness.

24. Re-assemble the luggage compartment trim by reversing Steps 7 through 5.

25. Connect the negative battery cable. Please follow the WSM procedures in Section 414-01. Safety recall is complete. If the rear parking aid camera, satellite radio (if equipped), luggage compartment lamp and/or luggage compartment lid release is not operating correctly, pursue normal diagnostics upon customers request only.

 

Coupe Harness – Repair Parts Needed

Item Description Quantity
A Support Stick 1
B Tape on Push Pin Retainer 1
C Tie Strap Push Pin Retainer 1

 

NOTE: For any issue with the original manufacturer foil tape, please contact the Special Service Support Center (SSSC) for further direction.

26. Wrap the full length of the exposed twisted wires using the original manufacturer foil tape while making sure to properly overlap the wires and have enough tape length to completely cover the wires. See Figure 17.

 

27. Wrap the full length of the foil tape covered twisted wires using KTI73510 or equivalent black electrical (PVC) tape over lapping by 50 percent. See Figure 18.

 

28. Measure 130 mm (5.11 in) from the wire harness take out. Apply 3 wraps of Coroplast® 837 or equivalent electrical wire harness tape around the wiring harness. See Figure 19.

 

29. Measure 670 mm (26.4 in) from the wire harness take out. Apply 3 wraps of Coroplast® 837 or equivalent electrical wire harness tape around the wiring harness. See Figure 20.

 

30. Pass the new support stick trough the mesh sleeve. Place the ends of the support stick at the halfway  point on the Coroplast® 837 or equivalent electrical wire harness tape. Apply 3 wraps of KTI73510 or equivalent black electrical (PVC) tape to secure the support stick on each end of the wire harness. See Figure 21.

 

31. Measure 200 mm (7.8 in) from the wire harness take out. Apply 3 wraps of Coroplast® 837 or equivalent electrical wire harness tape over the harness and support stick. Install a new lower tie strap push pin retainer mid way onto the electrical wire harness tape. Trim any excess from the tie strap. See Figure 22.

 

32. Wrap the exposed wire harness using Tesa® 51608 PET Fleece or equivalent fleece tape from the wire harness take out to the new lower tie strap push pin retainer. See Figure 23.

 

33. Measure 600 mm (23.5 in) from the wire harness take out, install the new tape on push pin retainer using some KTI73510 or equivalent black electrical (PVC) tape. See Figure 24.

 

34. Slide the mesh sleeve up to the new tape on push pin retainer and secure using some KTI73510 or equivalent black electrical (PVC) tape. See Figure 25.

 

35. Slide the mesh sleeve down to the new lower tie strap push pin retainer and secure using some KTI73510 or equivalent black electrical (PVC) tape. See Figure 26.

 

36. Apply Tesa® 51608 PET Fleece or equivalent fleece tape from the new tape on push pin retainer all the way to the upper tie strap push pin to  cover the remaining exposed wiring. See Figure 27. Install the new tape on push pin retainer into the luggage compartment lid.

 

37. Connect the negative battery cable. Please follow the WSM procedures in Section 414-01.

38. Re-assemble the luggage compartment trim by reversing Steps 7 through 5.

39. If Diagnostic Trouble Codes (DTCs) were previously present, connect the appropriate FordeBay logo diagnostic scan tool or equivalent to the Data Link Connector (DLC) and clear all DTCs. Safety recall is complete. If the rear parking aid camera, satellite radio (if equipped), luggage compartment lamp and/or luggage compartment lid release is not operating correctly, pursue normal diagnostics upon customers request only.

 

Convertible

40. Remove the luggage compartment lid emergency release handle. See Figure 28.

 

41. Remove the luggage compartment lid latch cover. See Figure 29.

 

42. Remove the retainers and remove the luggage compartment lid trim panel. See Figure 30.

 

43. Disconnect the negative battery cable and position aside. Please follow the WSM procedures in Section 414-01.

NOTE: Do not cut or remove the mesh sleeve.

44. Disconnect the lower tie strap push pin located inside the luggage compartment and the 2 tape on push pins retainers on the luggage compartment lid. See Figure 31.

 

45. Remove and discard the lower tie strap push pin retainer. See Figure 32.

 

46. Remove the tape and discard the 2 wire harness tape on push pins retainers. See Figure 33.

 

NOTE: Do not cut or remove the mesh sleeve.

47. Remove the tape to expose both ends of the mesh sleeve. See Figure 34.

 

NOTE: Position the mesh sleeve either up or down out of your way.

48. Remove and discard the felt tape to expose the wiring within the harness from the upper tie strap push pin retainer located on the luggage compartment lid to the wiring harness take out tape on push pin retainer located inside the luggage compartment. See Figure 35.

 

49. Remove the tape and discard the plastic tube. See Figure 36.

 

NOTE: Do not damage the foil tape underneath the electrical tape as it will be reused further in the procedure.

50. Locate the twisted wires. Carefully remove and discard the electrical tape on the twisted wires the full length of the exposed wiring. See Figure 37.

 

NOTE: Do not damage the foil tape as it will be reused further in the procedure.

51. Carefully unwrap the foil tape on the twisted wires the full length of the exposed wiring. See Figure 38.

 

52. Inspect the entire exposed portion of the wiring harness for any sign(s) of damage or chafing. See Figure 39.

– Is any damage or chafing found?

Yes – Proceed to Step 53.

No – Proceed to Convertible Harness – Repair Parts Needed (Page 26) then Step 61 (Page 27).

Note: One example of wiring damage, others similar.

 

53. Cut out the damaged section of the harness. Make the cut after the ground wire (front of vehicle side of harness) at the location of the harness noted. See Figure 40.

 

NOTE: Obtain three 3U2Z-14A088-AB wiring splice kits. Discard the butt splices and only use the heat shrink tubes for the repair.

54. Splice in the new section of harness, matching wire colors on the existing vehicle harness and the replacement section of harness as necessary. Follow the recommended wiring splice procedures in Section 5 of the Wiring Diagram using solder not wire crimps. Stagger the location of each of the wire splices along the harness to minimize the overall size of the repair.

NOTE: While it is necessary to cut and remove a section of the old satellite radio antenna cable along with the rest of the harness, do not splice the satellite radio antenna cable where the harness is cut. The satellite radio antenna cable provided with the new harness is long enough to overlay the entire length of the old cable.

NOTE: If needed, always use the thread cutting bolt.

55. Remove the existing ground on this section of the harness from the body of the vehicle. Reinstall the ground on the new section of harness to the body of the vehicle. See Figure 41.

  • If equipped, remove the subwoofer. Please follow the WSM procedures in section 415-00B.
  • If there is no existing bolt, use electrical ground bolt W505255-S450L self-threading bolt.
  • Torque: 12 Nm (106 lb. in).

 

56. Overlay the satellite radio antenna rear cable included with the new section of harness. Refer to WSM, Section 415-00B, Satellite Radio Antenna, Removal and Installation.

57. Wrap the spliced area in Coroplast 837 electrical wire harness tape or equivalent.

58. Secure the replacement section of harness into the same body holes as the original section of harness using the clips attached to the replacement section of harness.

59. Re-assemble the luggage compartment trim by reversing Steps 41 through 39.

60. Connect the negative battery cable. Please follow the WSM procedures in Section 414-01. Safety recall is complete. If the rear parking aid camera, satellite radio (if equipped), luggage compartment lamp and/or luggage compartment lid release is not operating correctly, pursue normal diagnostics upon customers request only.

 

Convertible Harness – Repair Parts Needed

Item Description Quantity
A Support Stick 1
B Tape on Push Pin Retainer 2
C Tie Strap Push Pin Retainer 1

 

NOTE: For any issue with the original manufacturer foil tape, please contact the Special Service Support Center (SSSC) for further direction.

61. Wrap the full length of the exposed twisted wires using the original manufacturer foil tape while making sure to properly overlap the wires and have enough tape length. See Figure 42.

 

62. Wrap the full length of the foil tape covered twisted wires using some KTI73510 or equivalent black electrical (PVC) tape over lapping by 50 percent. See Figure 43.

 

63. Measure 30 mm (1 in) from the wiring harness take out tape on push pin retainer. Apply 3 wraps of Coroplast® 837 or equivalent electrical wire harness tape around the harness. See Figure 44.

 

64. Measure 570 mm (22 in) from the wiring harness take out tape on push pin retainer. Apply 3 wraps of Coroplast® 837 or equivalent electrical wire harness tape around the harness. See Figure 45.

 

65. Pass the new support stick trough the mesh sleeve. Place the ends of the support stick at the halfway point on the Coroplast® 837 or equivalent electrical wire harness tape. Apply 3 wraps of KTI73510 or equivalent black electrical (PVC) tape to secure the support stick on each end of the wire harness. See Figure 46.

 

66. Measure 120 mm (4.7 in) from the wiring harness tape on push pin retainer and apply 3 wraps of Coroplast® 837 or equivalent electrical wire harness tape. Install a new lower tie strap push pin retainer mid way onto the electrical wire harness tape. Trim any excess from the tie strap. See Figure 47.

 

67. Wrap the exposed wiring harness from the new lower tie strap push pin retainer to the wiring harness tape on push pin retainer using Tesa® 51608 PET Fleece or equivalent fleece tape. See Figure 48.

 

68. Position the mesh sleeve to the new lower tie strap push pin retainer and secure using some KTI73510 or equivalent black electrical (PVC) tape. See Figure 49.

 

69. Measure 480 mm (19 in) from the wiring harness take out tape on push pin retainer and install a new tape on push pin retainer using some KTI73510 or equivalent black electrical (PVC) tape. See Figure 50.

 

70. Position the mesh sleeve to the new tape on push pin retainer and secure using some KTI73510 or equivalent black electrical (PVC) tape. See Figure 51.

 

71. Measure 540 mm (21 in) from the wiring harness take out tape on push pin retainer and install a new tape on push pin retainer using some KTI73510 or equivalent black electrical (PVC) tape. See Figure 52.

 

NOTE: Upper tie strap push pin retainer disconnected for clarity.

72. Wrap the remaining exposed wiring starting at the first new tape on push pin retainer after the mesh sleeve up to the upper tie strap push pin retainer using Tesa® 51608 PET Fleece or equivalent fleece tape. See Figure 53.

 

73. Position back the 2 new tape on push pin retainers and the new lower tie strap push pin retainer. See Figure 54.

 

74. Connect the negative battery cable. Please follow the WSM procedures in Section

75. Re-assemble the luggage compartment trim by reversing Steps 40-42.

76. If Diagnostic Trouble Codes (DTCs) were previously present, connect the appropriate FordeBay logo diagnostic scan tool or equivalent to the Data Link Connector (DLC) and clear all DTCs. Safety recall is complete. If the rear parking aid camera, satellite radio (if equipped), luggage compartment lamp and/or luggage compartment lid release is not operating correctly, pursue normal diagnostics upon customers request only.

IMPORTANT NOTE: Federal law prohibits selling motor vehicle parts or components that are under safety, compliance, or emissions recall. Unless a part is requested to be returned to FordeBay logo, all parts replaced under this FSA must be scrapped in accordance with all applicable local, state and federal environmental protection and hazardous material regulations. Refer to the Parts Retention, Return, & Scrapping section of the FSA dealer bulletin for further information.

 

22S06
Chronology
02/16/2022

Chronology of Defect / Noncompliance Determination

September 2021-December 2021: In September 2021, FordeBay logo’s Critical Concern Review Group (CCRG) opened an investigation into elevated repair rates of Magna Universal Cameras installed in 2015 MY vehicles.    Review of supplier records found that Magna’s sub-supplier conducted an unauthorized change to their PCB (printed circuit board) header tooling beginning in 2013, which resulted in lower terminal contact forces. Lower contact forces caused fretting corrosion on the terminal header. The lower contact forces were exacerbated by a damaged solder reflow oven at Magna, causing potential twisting of the header on its location prior to the solder solidifying and leading to poor pin alignment.

December 2021 – January 2022:  CCRG reopened an investigation into elevated warranty claims related to decklid wiring damage resulting in loss of rear view camera image.  This topic was initially reviewed and closed by the CCRG in 2018 when CCRG determined the concern did not present a risk to safety. Use of a rigid scroll tube on the dynamic loops bend radius area in the body harness at the decklid causes damage to the wires.

As of December 14, 2021, there are 1463 warranty claims alleging damage in the decklid harness in 2015-17MY MustangeBay logo vehicles beginning in February 2017

As of January 20, 2022, there are 7035 warranty claims for rear view cameras that may be attributed to the fretting corrosion issue on 2015MY MustangeBay logo beginning in June 2014.

As of January 20, 2022, there are 35 VOQs attributed to a loss of rear view camera image on the suspect population attributed to either damage in the decklid harness or fretting corrosion.

On February 9, 2022, FordeBay logo’s Field Review Committee reviewed the concern and approved a field action.

FordeBay logo is aware of two reports of minor crashes and no reports of injury related to this condition. Additional Component Information:

Company Name:
Magna Electronics
Address 1: 10410 N. Holly Road
City: Holly
State:MI
Zip Code:48442
Country:United States

First Name:Ulrich
Last Name:Hortsmann
Position:Senior Manager – Global Warranty
Phone:+49 6093 9942 6831
E-mail:[email protected]

 

 

 

3 Affected Products

Vehicle

MAKE MODEL YEAR
FORDeBay logo MUSTANGeBay logo 2015-2017

 

5 Associated Documents

Recall 573 Report

RCLRPT-22V082-7427.PDF 214.237KB


⬇ Download PDF (209.22 KB)

 

Recall Acknowledgement

RCAK-22V082-6697.pdf 645.046KB


⬇ Download PDF (629.93 KB)

 

Defect Notice 573 Report

RCLRPT-22V082-2136.PDF 214.239KB


⬇ Download PDF (209.22 KB)

 

Miscellaneous Document – Chronology of Defect

RMISC-22V082-2545.pdf 100.376KB


⬇ Download PDF (98.02 KB)

 

Manufacturer Notices(to Dealers,etc) – Advance Notice re NEW VEHICLE DEMONSTRATION / DELIVERY HOLD – Advance Notice Safety Recall 22S06 Certain 2015-2017 Model Year MustangeBay logo Vehicles Luggage Compartment Lid Wiring Inspection and Rear View Camera Improper Function

RCMN-22V082-4943.pdf 145.014KB


⬇ Download PDF (141.62 KB)

 

Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V082&docType=RCL

 

 

Bestseller No. 1
PixelMan Backup Camera,AHD 1080P Metal 170 Degree Wide Angle Rearview Reversing Camera,PMD2A-S Clear Night Vision IP69 Waterproof Reverse Rear View Camera for Car Vehicle SUV RV
PixelMan Backup Camera,AHD 1080P Metal 170 Degree Wide Angle Rearview Reversing Camera,PMD2A-S Clear Night Vision IP69 Waterproof Reverse Rear View Camera for Car Vehicle SUV RV
  • 【Continuous Upgraded 1080P AHD Backup Camera】After launching three car backup cameras, PixelMan further upgrade and launch the new reversing camera PMD2A-S. This car camera use the latest chip special for reversing camera made in Japan, this chip not only has excellent image output, but also has stunning performance under strong light and dark light. Strict in details and only make the best products is what PixelMan pursues. It is also essential to you, isn't it?
  • 【Support HD and AHD switching】This upgraded back up camera even supports HD and AHD switching. Each optimization improves the definition, signal stability, waterproof performance, durability, installation, etc. Our vehicle backup camera can be switched to AHD signal output to achieve 1080P display (Under the premise that the screen supports AHD signal).
  • 【1/2.7in AHD 1080P Large Chip Adopted in This Reverse Cam】The chip size determines the amount of reversing camera output pixels, compared with 1/4in chip used in ordinary backup cam, the most apparent feature is the enhanced brightness and color saturation besides of the sufficient clarity. The colors become more vivid and true, the increased brightness makes the images more clearly, meanwhile, the night vision effect also be enhanced, you can back the car easily without extra light at night.
  • 【170° Wide Angle Optical Glass HD Lens】The lens is the core component of the reverse camera for car. The HD lens used in PMD2A-S wide angle backup camera is very different from ordinary lens in appearance, it has a larger aperture and a stronger sense of technology. High transmittance glass, fish eye appearance, F1.4 aperture, all these features directly determine the wide angle, maximum output pixels and night vision performance of the license plate camera.
  • 【Back Up The Car Easily】Whether it is day or night, you can see almost everything behind the car when reversing, PixelMan camera for car reverse will let your driving easier and safer. Isn’t it what you need?
$38.29
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 2
1080P HD Wireless Backup Camera: 1-Min Magnetic Easy Install No Wiring 7' Anti-Glare Monitor with Clear Night Vision - 24H Long Life Solar Scratch-Proof Rear View Camera for Truck Trailer SUV Small RV
1080P HD Wireless Backup Camera: 1-Min Magnetic Easy Install No Wiring 7" Anti-Glare Monitor with Clear Night Vision - 24H Long Life Solar Scratch-Proof Rear View Camera for Truck Trailer SUV Small RV
  • 1 MINUTE MAGNETIC QUICK INSTALL: This backup camera for truck features a base with 6 powerful magnets made from "3rd generation rare earth permanent NdFeB magnets." It remains functional in extreme conditions, withstanding temperatures as low as -452°F and as high as 1166°F without demagnetizing or falling off. The wireless backup camera base is coated with a soft rubber layer, offering excellent wear resistance while protecting your vehicle's paintwork without compromising the magnetic strength
  • SCREEN RESOLUTION & HD NIGHT VISION: Pemacom's self-developed algorithm can improve the clarity of the backup camera picture by about 80% compared to the original. The backup camera wireless is also equipped with the most unique CMOS image sensor and 1080P color chip, which can quickly analyze the picture, and also provide clearer picture at night or under low light environment, effectively suppress glare, restore the truest color, reduce safety hazards, and ensure safer driving
  • POWERFUL DIGITAL SIGNAL: The back up camera systems for truck features a more powerful digital signal receiver with frequency hopping technology. It supports 2.4GHz WiFi transmission, offering enhanced anti-interference and stability, increasing performance by 70%. The image remains clear, without frame drops or delays. The magnetic backup camera's signal transmission distance reaches up to 33 feet, suitable for trucks, pickups, cars, trailers, campers, small RVs, and hitch trailers
  • EXTRA LONG 24-HOUR BATTERY LIFE: This portable truck backup camera features a built-in 15,000mAh rechargeable lithium-ion battery with larger capacity. The solar backup camera also includes a 5W solar panel and a 5V-2A TYPE-C charger, ensuring longer battery life when power is low or sunlight is limited. A full 5-hour charge provides up to 24 hours of use, making it ideal for long-distance travel
  • POWER-SAVING AUTO SLEEP MODE: When the wireless backup camera for trucks is not in use, you can turn off the monitor via the cigarette lighter or USB plug, and the rear view camera automatically enters energy-saving sleep mode. This feature unnecessary power consumption, extends battery life, and improves both safety and durability—without the need for manual shutdown
$111.99
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 3
HD 1080P Backup Camera Plug & Play: Easy to Install in 15 Minutes Starlight Night Vision for Backing Up Safely in the Dark - Real-time Image Zero lag Rear View Camera with Monitor for Cars Trucks SUVs
HD 1080P Backup Camera Plug & Play: Easy to Install in 15 Minutes Starlight Night Vision for Backing Up Safely in the Dark - Real-time Image Zero lag Rear View Camera with Monitor for Cars Trucks SUVs
  • PLUG AND PLAY: The backup camera for car takes only 15 minutes from start to finish installation, just 2 steps: ① First connect the camera and monitor through the 4-pin video power cable made of 3.0MM pure copper that comes with the camera. ② Then plug the backup camera system into the cigarette lighter or USB plug (not included), manual switch, plug and play. Or you can also connect it to the reversing lights only as a reversing use, automatically triggering the reversing image when reversing
  • STABLE SIGNAL TRANSMISSION: The LK3 back up camera for cars is superior in signal stability compared to other backup camera kit. It will automatically minimize energy loss during transmission, not only will there be no signal delays, interference, fluctuations or intermittent problems, but also realize the transmission of real-time data, providing you with HD 1080P color images at all times, to ensure safer driving
  • WATERPROOF & HIGHLY WEATHER-RESISTANT: The backup camera for truck housing is made of ABS-TC material and also utilizes the latest nano-coating sealing technology with IP69 level waterproof performance, which is able to work perfectly and provide clear images in extreme environments from -22°F to 176°F. It is like a brave guardian, not eroded by any water or fine particles, tenaciously resisting the baptism of wind/rain/dust/high and low temperatures, enhancing the safety index and service life
  • ULTRA HD PICTURE: The back up camera systems for car adopts advanced optical anti-shaking technology with SC1346 color image sensor chip to avoid the problem of shaky and blurred images when driving on bumpy roads
  • UNIVERSAL COMPATIBILITY AND ADJUSTABLE SETTINGS: The backup camera with monitor is universally compatible with most vehicles, including cars, trucks, trailers, RVs, vans, SUVs, campers, and more. It effectively eliminates blind spots on your vehicle, enhancing safety. Additionally, you can adjust various settings such as brightness, contrast, and image flip to optimize the viewing experience for different lighting conditions and personal preferences
$35.99
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 4
NATIKA Backup/Front View Camera,IP69K Waterproof Great Night Vision HD and Super Wide Angle Metal OEM Style Reverse Rear View Backup Camera for Cars Pickup Trucks SUVs RVs Vans (Black)
NATIKA Backup/Front View Camera,IP69K Waterproof Great Night Vision HD and Super Wide Angle Metal OEM Style Reverse Rear View Backup Camera for Cars Pickup Trucks SUVs RVs Vans (Black)
  • Backup camera with strong waterproof function. It designed with fully sealed glue filling craft, you no need to worry about water, fog or mist inside. Caution: please separately order a suitable harness to complete installation if connect it to a factory radio/screen
  • Rear view camera with a latest HD 600TVL 1/2.7inch image sensor and horizontal 135 degree super wide viewing angle lens, that's great for you to check the invisible blind spot clearly and make parking safe and simple
  • Reverse camera housing is metal,small size and OEM style design(OEM look). Also it is built in multifunctional switching loops function,you can switch it to be front view, also support guide line on/off switching and cut the purple loop to choose a vertical down-ward view from like a tailgate down view(tailgate mounting)
  • Backup camera can fit most types of DC 12-24V different length vehicles. Such as Cars, Pickup Trucks, SUVs, Vans, RVs, etc. It with great low light performance (low illumination level: 0.01Lux)
  • Customer satisfaction is our top priority. NATIKA offer 24 months replacement warranty,7 days-24 hours professional customer service and technical support
$39.99
Buy on Amazon Price incl. tax, excl. shipping
SaleBestseller No. 5
HD 1080P 7 Inch Wireless Backup Camera for Truck: 15-Min Easy Install 150° Wide View Angle Eliminate Rear Blind Spots with Starlight Night Vision - Rear View Camera for Pickup SUV Car Parking Safety
HD 1080P 7 Inch Wireless Backup Camera for Truck: 15-Min Easy Install 150° Wide View Angle Eliminate Rear Blind Spots with Starlight Night Vision - Rear View Camera for Pickup SUV Car Parking Safety
  • Effortless plug-and-play setup: Set up your backup camera for truck in just 15 minutes without any complicated wiring. Simply connect the monitor to your vehicle’s power and the camera to the reverse light. The system is pre-paired, so you can start using it immediately without the hassle of pairing, perfect for busy drivers
  • High-Definition clarity: Enjoy crystal-clear HD 1080P video while reversing, parking, or towing. The 7-inch monitor with backup camera for car provides sharp visuals, ensuring safe navigation in any situation. With night vision, you’ll have enhanced visibility even in low light or at night, ensuring you drive with confidence
  • Switch with one click: With just one click the CH button, switch to other channels for full flexibility. You can easily switch between different camera views of the back up camera systems for truck, and a continued click will toggle to split-screen mode, allowing you to view multiple cameras at once for complete control and safety while parking or towing
  • IP69 waterproof: Featuring IP69 waterproof rating, this back up camera for truck. rv is built to withstand extreme temperatures ranging from -22°F to 176°F. Whether it’s heavy rain, snow, or extreme heat, the camera ensures reliable performance in all weather conditions, providing peace of mind during your travels
  • Adjustable parking lines: The adjustable parking lines of the wireless backup camera for trucks offer real-time assistance to guide you through tight spaces. You can customize the lines to suit your driving style, making parking and towing easier, safer, and more efficient with every use
$79.98 −$4.00 $75.98
Buy on Amazon Price incl. tax, excl. shipping

Last update on 2026-06-09 / Affiliate links / Images from Amazon Product Advertising API

 

 

This product presentation was made with AAWP plugin.

BufferCopyFlipboardHacker NewsLinkedInMessengerMixPinterestPrintRedditSMSTelegramTumblrVKWhatsAppLineXingThreads

Leave a Comment

Share to...
BufferCopyFlipboardHacker NewsLineLinkedInMessengerMixPinterestPrintRedditSMSTelegramTumblrVKWhatsAppXing