| 1.6L GTDI – OVERHEAT IN COLD AMBIENT TEMPERATURES AT -12 DEGREES CELSIUS (10 DEGREES FAHRENHEIT) OR BELOW WITH DTCS P0217 AND P1299 |
FORD : | 2013 Fusion |
2013 Fusion vehicles equipped with a 1.6L Gasoline Turbocharged Direct Injection (GTDI) engine may exhibit an intermittent overheat in cold ambient temperatures of -12 °C (10 °F) and below while traveling at highway speeds with diagnostic trouble codes (DTCs) P0217 and P1299 present.
SERVICE PROCEDURE
- Connect the Ford Integrated Diagnostic System (IDS) service tool or Scan Tool to the data link connector (DLC). Are DTCs P0217 and P1299 present in the powertrain control module (PCM)?
- Yes – proceed to Step 2.
- No – this procedure does not apply. Refer to Workshop Manual (WSM).
- Is the engine coolant at the proper level and free from contamination?
- Yes – proceed to Step 3.
- No – this procedure does not apply. Refer to WSM.
- Disconnect the engine coolant temperature (ECT) sensor and check for contamination in the harness side connector. Was contamination found?
- Yes – this procedure does not apply. Refer to WSM.
- No – proceed to Step 4.
- With the IDS scan tool, go to the Datalogger, select PCM, select High Cooling Fan (HCF#) and Low Cooling Fan (LCF#) parameter identification (PIDs) and active command both low and high speed fan operation. Did the fans operate at both low and high speed?
- Yes – proceed to Step 5.
- No – this procedure does not apply. Refer to WSM.
- Is the vehicle equipped with active grille shutters?
- Yes – while still in the Datalogger, select the active grille shutters Mode PID (GRILL_A_CMD#) and active command the grille shutters. Did the active grille shutters close and open properly?
- Yes – proceed to Step 6.
- No – this procedure does not apply. Refer to WSM.
- No – the vehicle is not equipped with active grille shutters, proceed to Step 6.
- Yes – while still in the Datalogger, select the active grille shutters Mode PID (GRILL_A_CMD#) and active command the grille shutters. Did the active grille shutters close and open properly?
- Reprogram the PCM to the latest calibration using IDS or Ford J2534 release 93.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
- Replace the coolant bypass solenoid valve.
BM5Z-18495-C
Ford BM5Z-18495-C Genuine Valve Assembly
Last update on 2026-06-18 / Affiliate links / Images from Amazon Product Advertising API | Coolant Bypass Solenoid Valve |
Service Information & Reprogramming
Software necessary to program electronic modules to the latest calibration level, perform module initialization (PATS), and set Programmable Parameters on Ford, Lincoln and Mercury vehicles.
Ford Module Programming (FMP) is a software application that allows subscribers to program electronic modules on Ford, Lincoln and Mercury vehicles. It can be used for:
- Reprogramming emission-related (OBDII) modules on some vehicles manufactured in 1995 and all vehicles manufactured from 1996 to the present
- Reprogramming or reconfiguring non-emission-related modules on many vehicles (UBP and MS-CAN not supported)
In addition, module initialization (PATS) functions such as Keycode Erase/Reprogram and PCM Parameter Reset can be done using this application.
No products found.
Last update on 2026-06-10 / Affiliate links / Images from Amazon Product Advertising API
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
Last update on 2026-06-09 / Affiliate links / Images from Amazon Product Advertising API
No products found.
No products found.
Latest Calibration Information
Module Build Data (As-Built)
Use VIN to obtain As-Built data
www.motorcraftservice.com
Last update on 2026-06-09 / Affiliate links / Images from Amazon Product Advertising API
No products found.
- Delivers serious jump-starting power with 1000 peak amps and 500 instant starting amps
- Reverse polarity alarm alerts when there is an improper connection; Connect the clamps to the battery, turn on the switch and start your vehicle. All Metal Powder Coated Clamps
- Features a 120 PSI air compressor to help inflate tires with low pressure; High-powered LED light rotates 270 degrees to help you work in the dark
- Built-in 12V DC outlet and USB port provide portable power for electronic devices; Includes a limited 1 year manufacturer warranty
- Jump starter should be charged every 30 days when not in use; Charges using a standard household extension cord (sold separately)
Last update on 2026-06-10 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.