| RATTLE NOISE UNDER VEHICLE – HEAT SHIELD CONTACT TO FLOOR PAN – VEHICLES BUILT ON OR BEFORE 8/7/2007 |
:
2006-2007 Front Wheel Drive (FWD) Fusion, Milan, 2007 MKZ vehicles built on or before 8/7/2007 and 2006 Zephyr vehicles may exhibit a customer concern of a rattle/vibration noise perceived to be coming from the console area or under the vehicle.
The rattle/vibration noise is most prominent during windy days where a crosswind is present and commonly occurs at approximate vehicle speeds between 50-70 MPH (80-116 Km/h).
SERVICE PROCEDURE
- Raise the vehicle on a hoist.
- Inspect the heat shield wings positioned in the rear portion of the exhaust shield, above the muffler. (Figure 1)
Figure 1
- Verify that the two (2) wings are not touching the floor pan tunnel (Figure 2). If they are, proceed to Step 4. If not, follow the normal service diagnostic procedures.
Figure 2
- Pull the wings down vertically to achieve a minimum clearance of 3/4″ (20 mm). (Figures 3 and 4)
Figure 3
Figure 4
Bestseller No. 1
Racewill Titanium Pipe Shield, 6" x 12" Exhaust Heat Shield
- [Advanced Heat Protection] Advanced double-layer material design, outer layer-titanium material, Inside Inside-temp silica fabricc. Heat protection up to 1350°F.
- [Easy Installation] Our unique rivet-based pipe standoff brackets and pipe clamps make installation a breeze.
- [Reduce Heat] Unique shield bracket design provides an air gap between shield and ducting, which together provide maximum cooling and heat dissipation potential.
- [Flexible Positioning] The easy-to-remove 3.5" hose clamp allows you to adjust it to your needs and preferences.
- [Universal Fit] Flexible shields can be installed on almost any shape of pipe. Due to the special material, we would like to remind you to wear gloves during installation.
Bestseller No. 2
SunplusTrade 2" x 50' Black Exhaust Heat Wrap Roll for Motorcycle Fiberglass Heat Shield Tape with Stainless Ties
- Package includes one 2 inch X 50 feet Heat Wrap with (pack of 6) 12" Stainless Steel (304) Locking Zip Ties.
- The exhaust heat wrap tape can withstand 1400F direct/2000F radiant heat.
- High resistance to abrasions, oil spills, temperatures and vibration breakdown
- The thermal heat wrap can reduce heat under hood up to 50%
- Universal fitment for cars and motorcycles performance parts
Bestseller No. 3
Racewill Titanium Pipe Shield, 6" x 24" Exhaust Heat Shield with Gloves
- [Advanced Heat Protection] Advanced double-layer material design, outer layer-titanium material, Inside Inside-temp silica fabricc. Heat protection up to 1350°F.
- [Reduce Heat] Unique shield bracket design provides an air gap between shield and ducting, which together provide maximum cooling and heat dissipation potential.
- [Upgrade Rivet Design] Our muffler heat shield is equipped with a washer under the rivet head to prevent the rivet from breaking or falling off during installation.
- [Flexible Positioning] The easy-to-remove 3.5" hose clamp allows you to adjust it to your needs and preferences.
- [Universal Fit] Flexible insulation shield can be installed on almost any shape of pipe. Due to the special material, we would like to remind you to wear gloves during installation.
Bestseller No. 4
UNIFAMILY Embossed Exhaust Heat Shield Automotive, 12" x 39" Aluminum Exhaust Heat Wrap with 20 Pcs Cable Metal Zip Ties, Exhaust Wrap Heat Barrier Shield, Heat Wrap for Exhaust pipes
- Heat Resistance: The automotive heat shield can withstand sustained high temperatures up to 1022°F/ 550 °C, suitable for mufflers, chassis, fuel tanks, catalytic converters, engine compartments, batteries, air intakes and more.
- Flexible and Easy to Use: Exhaust pipe wrap heat shield is easy to cut, measuring approximately 12 x 39 inches / 30.5 cm x 1 m, 0.02 inches / 0.5 mm thick, easy to bend and cut to customized installation shapes, suitable for firewalls, transmission passages, chassis, or fuel tanks.
- High quality: Car exhaust heat shield is made of insulated aluminum sheet material, heavy duty embossed and corrosion resistant. This embossing enhances the heat dissipation of the shield as it allows for smoother air flow. Motorcycle heat shield has good heat insulation effect, can withstand constant high temperature, effectively protect the parts.
- Package Included: You will receive 1 roll of exhaust heat shield, 20 cable metal zippers, easy to use, easy to cut and shape; please pay attention to the sharp edges of the product when disassembled.
- Wide Application: Aluminum heat shield is perfect for mufflers, chassis, fuel tanks, catalytic converters, engine compartments, batteries, air intakes, etc.; Large size for daily use, you just need to trim the sheet to the desired shape or size to meet your various project needs.
Bestseller No. 5
LEDAUT 2" x 50' Titanium Exhaust Heat Wrap Roll for Motorcycle Fiberglass Heat Shield Tape with Stainless Ties
- 2"X50' Titanium Wrap with (pack of 16) Stainless Steel(304) Locking Ties.
- Before installing, soak the header heat wrap in water so that the fiberglass will not flying about. Wear gloves to avoid itching. Wrap it around your exhaust pipe, using overlap to hold it in place and simply use stainless ties to secure the ends in place.
- High resistance to abrasions, oil spills, temperatures and vibration breakdown.
- The exhaust heat wrap tape can withstand 1800F direct/2500F radiant heat.
- The thermal heat wrap reduces heat under hood up to 50% and improving car And motorcycle Performance
This product presentation was made with AAWP plugin.