NHTSA ID Number: 10202711
Manufacturer Communication Number: TSB 21-2354
Summary
Some 2021 Bronco vehicles built on or before 23-Aug-2021 may experience a charging system fault message displayed in the instrument panel cluster (IPC) and diagnostic trouble codes (DTC) U012D, U0284 and/or U0285 stored in the powertrain control module (PCM). This may be due to water intrusion in the active grille shutter connector. To correct this condition, follow the Service Procedure to inspect for water intrusion in the active grille shutter harness connector and repair as needed.
Model:
2021 Bronco
Issue: Some 2021 Bronco vehicles built on or before 23-Aug-2021 may experience a charging system fault message displayed in the instrument panel cluster (IPC) and diagnostic trouble codes (DTC) U012D, U0284 and/or U0285 stored in the powertrain control module (PCM). This may be due to water intrusion in the active grille shutter connector. To correct this condition, follow the Service Procedure to inspect for water intrusion in the active grille shutter harness connector and repair as needed.
Action: Follow the Service Procedure steps to correct the condition if the vehicle meets all of the following criteria:
- 2021 Bronco
- Built on or before 23-Aug-2021
- Charging system fault message displayed in the IPC
- DTCs U012D, U0284 and/or U0285 stored in the PCM
Parts
| Service Part Number | Quantity | Description |
| HU2Z-14S411-LA | 1 | Connector C1767 Service Replacement Pigtail |
| MB3Z-10884-B | 1 | Active Grille Shutter Motor |
Service Procedure
1. Remove the lower active grille shutter and harness assembly from the vehicle. Refer to Workshop Manual (WSM), Section 501-02, Front End Body Panels > Removal and Installation > Active Grille Shutter.
NOTE: When removing the bumper, the brush guard (if equipped) does not require removal.
2. Disconnect the active grille shutter connector C1767. Is there evidence of water intrusion (trapped water or corrosion) inside connector C1767 harness and/or component side?
(1). Yes – proceed to Step 3.
(2). No -proceed to Step 4.
3. Replace the active grille shutter motor.
(1). Remove the center active grille shutter motor clip. (Figure 1)
Figure 1
(2). Remove the vertical fin clips on each side. (Figure 2)
Figure 2
(3). Remove the bottom fins located on each side. (Figure 3)
Figure 3
(4). Remove the active grille shutter motor. (Figure 4)
Figure 4
(5). Install the new active grille shutter motor by reversing the installation procedure.
4. Replace the connector C1767 by soldering in a new service pigtail. Refer to Wiring Diagram Cell 005, Page 5.
5. Install the lower active grille shutter onto the vehicle. Refer to WSM, Section 501-02, Front End Body Panels > Removal and Installation > Active Grille Shutter.
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
FORD | BRONCO | 2021 |
1 Associated Document
Manufacturer Communications
21-2354
13 October 2021
- Package Included: 50 pcs red waterproof wiring connectors for 22, 20, 18, 16 gauge wires, 40 pcs blue waterproof wiring connectors for 16, 14 gauge wires, 10 pcs yellow waterproof wiring connectors for 12, 10 gauge wires—total 100 pcs
- Premium Copper Core: The butt splice terminals use seamless and high-quality thick copper tubular, which makes the connection project safer! Fix the wire firmly, increase current flow, and decrease voltage drop
- Wide Usage: Our heat shrink wire connector is ideal for marine, automobile, industry, electrical and electronics. Whether working on boat, vehicle, RC car, home, scientific project, car stereo, or electrical DIY, the crimp connectors will work well
- 3:1 Heatshrink Ratio: The heat shrink butt connector has dual-wall shrinking tube and inside hot melt glue, providing a fully safe seal and wire corrosion. Its dual wall insulation seals against moisture corrosion, air leakage, and can be used underground
- AIRIC Brand Advantages: As a professional manufacturer of electrical accessories, we own a large leading wire connectors factory and get UL, CE, ROHS, SGS, and ISO9001-2005 international quality system certification
- COMPLIANT WITH ALL RELEVANT STANDARDS:With Haisstronica 330PCS( A.W.G.:22-16 150 PCS,16-14 100 PCS,12-10 32 PCS,26-24 48 PCS) heat shrink waterproof wire connectors are compliant with ROHS, ISO 9001:2008, SGS, and CE standards
- HIGH-QUALITY COPPER CORE:Heat shrink butt connectors use a copper core with a higher thickness rating.This makes your connection project safer and better meets our customers’ quality needs
- HIGH-QUALITY HEAT SHRINK:Translucent heat shrink tubing provides high tensile strength and resistance to stretch and minimize mechanical damage.The thick barrel ensures a strong crimp every time.The inner wall of the heat-shrinkable tube has enough hot melt adhesive to ensure waterproof performance reliability.Your wire will never slip out of these heat shrink wire connectors
- RECOGNIZABLE:Tubings of varying colors with easily recognizable wire gauge markings. Simply measure the wiring, and by checking the mark of wire gauge of the polyolefin tubing, then you can quickly choose the right connector
- WIDE APPLICATIONS: High quality 3:1 shrinkage tubing has a heat-activated sealant lining to provide complete secure seal. It's flame-retardant, waterproof, and can be used underground. Compliant with all electrical standards, Perfect for marine and automobile applications, whether you are working on your boat, Vehicle, Home or scientific project
- Solid Crimp: Seamless tinned copper barrel grips each wire without splitting, giving these butt connectors a strong hold that helps reduce the risk of short circuits; The thick copper barrel helps reduce voltage drop, supports high current flow, and minimizes heat buildup for dependable electrical connectors
- Watertight Seal: These heat shrink butt connectors feature dual-wall tubing with a 3:1 shrink ratio and a heat-activated adhesive lining, creating a secure 360-degree seal around each crimp; The dual-wall tubing helps seal out moisture and reduce corrosion, making these heat shrink wire connectors suitable for underground conduit, engine bays, and other demanding environments
- Color-Coded Sizing: Color-coded tubing lets you quickly identify the right butt splice connectors by wire gauge, with red for AWG 22–16, blue for AWG 16–14, yellow for AWG 12–10, black for AWG 14–12, and white for AWG 24–22; Strip, insert, and crimp with a standard tool, then apply heat to create secure wire connectors for a wide range of wiring projects
- Wide Applications: Ideal for marine, automotive, home, trailer, and outdoor wiring projects; These marine butt connectors provide dependable connections for boat consoles, bilge pumps, vehicle wiring, outdoor speakers, and other electrical installations where moisture protection is important
- Available Options: This assortment includes red, blue, and yellow waterproof butt connectors for wire sizes from AWG 22–10; Choose the appropriate color-coded connector to match your wire gauge for marine wire connectors, vehicle harnesses, home electrical wiring, and other electrical applications
- Tinned Copper Core: Butt connectors use a heavy-duty copper core, strong crimp, higher conductivity
- Package Includes: 100Pcs Blue heat shrink butt connectors that can be used on wire AWG from 16 to 14
- Solderless Crimping: Insert the wires to be connected, crimp both sides with crimping pliers, and then heat with a heat gun
- 3:1 Shrink Ratio: Marine grade heat shrink tubing provides high tensile strength and enough hot melt adhesive inside the tubing to ensure waterproof performance, your wires will never slip out of the wire connectors
- Wide Application: Wire connectors are waterproof, stable, and corrosion resistant and are used in the automotive, marine, electrical, and electronic industries
- Package Includes: Comes with 700 red AWG 22-16, 600 blue AWG 16-14, 150 yellow AWG 12-10 and 50 white 26-24 connectors. Suitable for industrial, automotive, marine, electrical and electronics wiring with an operating temperature of -60℉ to 260℉ and min shrink temperature 175℉, meeting daily needs.
- Tinned Copper Core: Made of thickened 99.9% tinned-copper cores, heat shrink wire connectors combine marine-grade polyolefin heat shrink tubing with adhesive-lined double-insulated tubing. Thick copper can low voltage drop, support high current with low heat, ensuring strong crimp and excellent conductivity to reduce short circuits.
- Easy, Solder-Free Use: Strip wire insulation, insert into connector, crimp with pliers and heat it evenly with a heat gun in seconds. Butt connectors heat shrink tubing with wire gauge markings are easy to identify and transparent tubing makes inspection easier.
- 3:1 Shrink Ratio: The hot melt adhesive forms an all-around IP67 waterproof and corrosion-restricted seal. Double-insulated tube is flame-retardant and marine-grade butt connectors support underground use.
- Secure to Last: Polyolefin tubing of wire connectors provides high tensile strength to resist mechanical damage and external abrasion. Seamless tube barrel and thick tinned copper make connection secure and reliable.
SEOCONTENT-START
Warranty Status: Eligible under provisions of New Vehicle Limited Warranty (NVLW)/Service Part Warranty (SPW)/Special Service Part (SSP)/Extended Service Plan (ESP) coverage. Limits/policies/prior approvals are not altered by a TSB. NVLW/SPW/SSP/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool. Labor Times Description Operation No. Time 2021 Bronco: Retrieve DTCs, Inspect Harness, Replace Connector Following The Service Procedure (Do Not Use With Any Other Labor Operations) 212354A 1.5 Hrs. 2021 Bronco: Retrieve DTCs, Inspect Harness, Replace Connector And Active Grille Shutter Motor Following The Service Procedure (Do Not Use With Any Other Labor Operations) 212354B 1.6 Hrs. Repair/Claim Coding Causal Part: 15A211 Condition Code: 01
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.