NHTSA ID Number: 10203708
Manufacturer Communication Number: TSB 21-2419
Summary
Some 2018-2021 Expedition/Navigator vehicles built on or before 02-Aug-2021 may exhibit a condition where the gap hiders of the load floor compartment come detached. This may be due to the joint between the gap hiders and the bin. To correct the condition, follow the Service Procedure steps to replace the damaged gap hiders.
8 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| FORD | EXPEDITION | 2018-2021 |
LINCOLN | NAVIGATOR | 2018-2021 |
Model:
Ford
2018-2021 Expedition
Lincoln
2018-2021 Navigator
Issue: Some 2018-2021 Expedition/Navigator vehicles built on or before 02-Aug-2021 may exhibit a condition where the gap hiders of the load floor compartment come detached. This may be due to the joint between the gap hiders and the bin. To correct the condition, follow the Service Procedure steps to replace the damaged gap hiders.
Action: Follow the Service Procedure steps to correct the condition on vehicles that meet all the following criteria.
- 2018-2021 Expedition/Navigator
- Built on or before 02-Aug-2021
- One or both gap hiders detached and/or damaged
Parts
| Service Part Number | Quantity | Description |
| JL1Z- 7845455-BB | 1 | Left Gap Hider Kit – Blue Bay |
| JL1Z- 7845455-BC | 1 | Left Gap Hider Kit – Mahogany Red |
| JL1Z- 7845455-BD | 1 | Left Gap Hider Kit – Dark Slate |
| JL1Z- 7845455-BE | 1 | Left Gap Hider Kit – Ebony |
| JL1Z- 7845455-BF | 1 | Left Gap Hider Kit – Espresso |
| JL1Z- 7845455-CB | 1 | Right Gap Hider Kit – Blue Bay |
| JL1Z- 7845455-CC | 1 | Right Gap Hider Kit – Mahogany Red |
| JL1Z- 7845455-CD | 1 | Right Gap Hider Kit – Dark Slate |
| JL1Z- 7845455-CE | 1 | Right Gap Hider Kit – Ebony |
| JL1Z- 7845455-CF | 1 | Right Gap Hider Kit – Espresso |
Service Procedure
- Remove the load floor storage compartment. Refer to Workshop Manual (WSM), Section 501-05, D-Pillar Trim Panel – Short Wheelbase, Steps 1-8.
- Flip the load floor compartment upside down and remove the springs from the gap hider.
(1). Remove the spring from the load floor compartment. (Figure 1)
(2). Push down on the spring. (Figure 2)
(3). Slide out and discard the spring(s) attached to the gap hider. (Figure 3)
- Remove the gap hider from the bin by breaking the push nuts using a trim fastener remover. (Figure 4)
- Remove the remaining push nuts in the bin by drilling out with an 11/32 inch (9 mm) drill bit. (Figure 5)
(1). Vacuum the load floor compartment and the carpet of the gap hider for remaining push nut debris before installation.
- Install the new gap hider carpet-side down and insert the posts through the corresponding holes on the driver and/or passenger side.
- Flip the load floor compartment upside down and use a magnet to locate the push nuts into the gap hider posts. (Figure 6)
- Use a 1/2 inch drive ratchet extension with a 10 mm impact socket to locate the push nut into the post and press firmly to assure a correct installation. (Figure 7)
(1). Make sure that the push nuts are completely seated. If they are not completely seated the gap hider may loosen during the folding process.
- Install new springs.
NOTE: The smaller right hand gap hider has 2 springs. The larger left hand gap hider has 3 springs.
(1). Insert the spring into the gap hider. (Figure 8)
(2). Push up on the spring. (Figure 9)
(3). Insert the spring into the load floor compartment. (Figure 10)
- Reinstall the load floor compartment. Refer to WSM, Section 501-05, D-Pillar Trim Panel – Short Wheelbase.
SEOCONTENT-START
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&vers… 1/9
TECHNICAL SERVICE BULLETIN
Load Floor Compartment – One Or Both Gap Hiders Detached And/OrDamaged From The Bin – Built On Or Before 02-Aug-2021
21-2419
24 November2021
Model:
Ford
2018-2021 Expedition
Lincoln
2018-2021 Navigator
Issue:
Some 2018-2021 Expedition/Navigator vehicles built on or before 02-Aug-2021 may exhibit a condition wherethe gap hiders of the load floor compartment come detached. This may be due to the joint between the gap hidersand the bin. To correct the condition, follow the Service Procedure steps to replace the damaged gap hiders.
Action:
Follow the Service Procedure steps to correct the condition on vehicles that meet all the following criteria.
• 2018-2021 Expedition/Navigator
• Built on or before 02-Aug-2021
• One or both gap hiders detached and/or damaged
Parts
Service Part Number
Quantity
Description
JL1Z- 7845455-BB
1
Left Gap Hider Kit – Blue Bay
JL1Z- 7845455-BC
1
Left Gap Hider Kit – Mahogany Red
JL1Z- 7845455-BD
1
Left Gap Hider Kit – Dark Slate
JL1Z- 7845455-BE
1
Left Gap Hider Kit – Ebony
JL1Z- 7845455-BF
1
Left Gap Hider Kit – Espresso
JL1Z- 7845455-CB
1
Right Gap Hider Kit – Blue Bay
JL1Z- 7845455-CC
1
Right Gap Hider Kit – Mahogany Red
JL1Z- 7845455-CD
1
Right Gap Hider Kit – Dark Slate
JL1Z- 7845455-CE
1
Right Gap Hider Kit – Ebony
JL1Z- 7845455-CF
1
Right Gap Hider Kit – Espresso
Warranty Status:
Eligible under provisions of New Vehicle Limited Warranty (NVLW)/Service Part Warranty(SPW)/Special Service Part (SSP)/Extended Service Plan (ESP) coverage. Limits/policies/prior approvals are notaltered by a TSB. NVLW/SPW/SSP/ESP coverage limits are determined by the identified causal part and verifiedusing the OASIS part coverage tool.
Labor Times
Description
OperationNo.
Time
2018-2021 Expedition/Navigator: Replace Gap Hiders Following The Service Procedure (Do NotUse With Any Other Labor Operations)
212419A
0.6Hrs.
Repair/Claim Coding
Causal Part:
7845455
Condition Code:
01
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 2/9
Service Procedure
1.
Remove the load floor storage compartment. Refer to Workshop Manual (WSM), Section 501-05, D-Pillar TrimPanel – Short Wheelbase, Steps 1-8.
2.
Flip the load floor compartment upside down and remove the springs from the gap hider.
(1). Remove the spring from the load floor compartment. (Figure 1)
Figure 1
(2). Push down on the spring. (Figure 2)
Figure 2
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 3/9
(3). Slide out and discard the spring(s) attached to the gap hider. (Figure 3)
Figure 3
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 4/9
3.
Remove the gap hider from the bin by breaking the push nuts using a trim fastener remover. (Figure 4)
Figure 4
4.
Remove the remaining push nuts in the bin by drilling out with an 11/32 inch (9 mm) drill bit. (Figure 5)
(1). Vacuum the load floor compartment and the carpet of the gap hider for remaining push nut debris beforeinstallation.
Figure 5
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 5/9
5.
Install the new gap hider carpet-side down and insert the posts through the corresponding holes on the driverand/or passenger side.
6.
Flip the load floor compartment upside down and use a magnet to locate the push nuts into the gap hider posts.(Figure 6)
Figure 6
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 6/9
7.
Use a 1/2 inch drive ratchet extension with a 10 mm impact socket to locate the push nut into the post and pressfirmly to assure a correct installation. (Figure 7)
(1). Make sure that the push nuts are completely seated. If they are not completely seated the gap hider mayloosen during the folding process.
Figure 7
8.
Install new springs.
NOTE: The smaller right hand gap hider has 2 springs. The larger left hand gap hider has 3 springs.
(1). Insert the spring into the gap hider. (Figure 8)
Figure 8
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 7/9
(2). Push up on the spring. (Figure 9)
Figure 9
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 8/9
(3). Insert the spring into the load floor compartment. (Figure 10)
Figure 10
9.
Reinstall the load floor compartment. Refer to WSM, Section 501-05, D-Pillar Trim Panel – Short Wheelbase.
© 2021 Ford Motor Company
All rights reserved.
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, andequipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides informationthat could assist in proper vehicle service. The procedures should not be performed by “do-it-yourselfers”. Do not assume that a conditiondescribed affects your car or truck. Contact a Ford or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policyand Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article.
12/1/21, 11:19 AM https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/defau…
https://www.fordservicecontent.com/Ford_Content/vdirsnethttps://static.oemdtc.com/TSB/EU/~WTSB21-2419/US/EN/~UEmployee/default.aspx?VIN=&ver… 9/9
The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supersedethis information with updates. The most recent information is available through Ford Motor Company’s on-line technical resources.
SEOCONTENT-END
1 Associated Document
Manufacturer Communications
21-2419
24 November 2021
MC-10203708-0001.pdf 1302.331KB
- 【For 2018-2024 Ford Expedition/Lincoln Navigator】The JTYZSM Trunk Mat with Backrest Mat Set is designed exclusively for the 18-24 Ford Expedition/Lincoln Navigator(Not for Max or L Models).Please confirm your car model can be used before purchase.
- 【Durable & wearable Material】The Trunk Mat with Backrest Mat set is made of high quality TPE, with high strength and resilience, hard to deform, not easy to aging, not easy to break and resistant to dirt.
- 【Non-Slip Protective & Easy to Clean】The cargo mats set features a non-slip ribbed surface to prevent your seat from being soiled or damaged when items hit it when you brake while driving. Whether there is dust, dirt or sand on the mat, it only takes a few minutes to clean it with clean water or a damp towel.
- 【Easy to Install】The trunk mats just needs to put it in the correct position of the car.It's very easy to install and remove, adjust the position without any tools.
- 【Warranty】If our mats is damaged during transportation or normal use, please contact us immediately and we can replace it with a new one for you. We will do our best to solve the problem for every customer!
- Optimal Solution: Our small envelope style cargo net is a must-have accessory for your car! Easy to install and practical, this accessory is key to preventing any load from moving in the trunk for a safer and more comfortable drive.
- Easy to Install: The car storage rear trunk elastic stretchable organizer is designed for individual car models. The net is very easy and quick to install, as well as secure and durable. Because it is designed for individual car models, no additional devices or new holes are needed for installation.
- Made to Last: The mesh net is made entirely out of nylon, a heavy-duty material that is sturdy, resilient, and very long-lasting. The trunk net is lightweight and easy to put away when not used. Elastic & Stretchable!
- Compatibility: This trunk net organizer for Ford Expedition 2018-2026 / Lincoln Navigator 2018-2026 is designed specifically for each car model. Net comes with 2 Loops on Top and 2 Hooks on the Bottom. Attach to 2 Hooks on Top and 2 Loops on Bottom.
- Keeping Your Car Organized: The car cargo organizer comes with 3 locks for fixing the mesh on top so that objects from the mesh cannot fall out. It stops your groceries, sports equipment, or other accessories from moving in the trunk.
- 【🚗Custom Fit for 2018-2024 Ford Expedition MAX (Only Fit 7 Seats) Non Short】Floor Mats & Large Trunk mat With Backrest protection.The WAYIDSS floor mats is high-precision laser measured, which means that our customized fit will provide the best coverage range, looking like the mat included with your car.
- 【🚗SAFE AND COMFORTABLE MATERIALS】 The accessory pad for 2018-2024 Ford Expedition MAX made of TPE, free of latex and PVC, 100% recyclable, and odorless.WAYIDSS mat is both soft and durable. More importantly, they can withstand extreme weather conditions, so you don't have to worry about cracking, curling, or mat damage.
- 【🚗HIGH WALL DESIGN】Beveled edges prevent wall bending. The high wall design can prevent any debris inside the lining and on the floor mats. High grooves and ridges are designed for drainage.
- 【🚗EASY TO CLEAN】The garden hose gun can easily clean the floor mat for 2018-2024 Ford Expedition MAX. There is also a damp cloth and some tap water available. Daily maintenance is really easy.
- 【🚗SINCERE SERVICE】We know that you want to choose the best for your car, and the WAYIDSS mat is perfect for your vehicle and provides protection. This is what WAYIDSS has done for you. If you have any questions, please feel free to contact us, and our after-sales team is willing to serve you.
- PERFECT STORAGE SOLUTION - Specifically crafted for Lincoln Navigator 2018-2026. Our trunk net, will help you store all your belongings together without worrying about space cluttering, goods rolling around, or liquid spills. Get easy access to things with our car net! No more mess or lost items!
- PREMIUM QUALITY & LONG DURABILITY - Each hammock-style design cargo net is custom-crafted according to the vehicle's year. Made of non-toxic black polypropylene, which has a 3x greater elastic range and 2x longer durability compared to similar nets
- INSTALLATION WITHIN SECONDS - The trunk net attaches quickly and easily to the mounting points in the cargo area and folds flat when not in use. Easy net closure is made possible by upside-down hooks. No need for extra accessories to install!
- EXTREMELY DURABLE - Car trunk net can easily hold large, bulky, fragile, & rounded objects. Great for carrying groceries, sports equipment, luggage, clothes, & so much more. An easy way to keep belongings organized when traveling or shopping
- HIGHEST STANDARDS - All trunk accessories are made with premium materials and comply with all manufacturing standards. We provide a 1-year warranty on our truck cargo netting. Dedicated to car owners and those who cherish cleanliness and tidiness
- PERFECT FIT: Custom fit design for Expedition Max 7/8 Seats 2025-2026, edge to edge for maximum coverage and protection with TPE (thermoplastic elastomer) material which ensures your more strength, resilience, durability and elasticity.
- ALL SEASONS AND DURABILITY: The Expedition Max 7/8 Seats Cargo Liner with Backrest Mats durable tray is easy to install and can be used all weather, which is stain-resistant, waterproof and anti-slip, preventing your carpet from rain, slush, snow, mud and protect your car during winter or summer.
- ODORLESS AND NON-TOXIC: The cargo liner with Backrest Mats is made with non-toxic and odorless TPE material. No foul smell will be produced even in high temperature. Bring you and your families a safer and more comfortable interior car environment.
- EASY TO CLEAN: Our Expedition Max 7/8 Seats cargo liner with Backrest Mats is easy to clean. No matter with dust, dirt or sand on the mats, just take several minutes wash off it with water or damp towel.
- QUALITY SERVICE: If there are any quality or defect issues when you get the car mats, please do contact us. We'll be glad to help you solve the problems.Your satisfaction is our ultimate goal.
This product presentation was made with AAWP plugin.