Headliner Sag by the Center High Mounted Stoplamp – 2014-2015 Ford Fusion

“This site contains affiliate links for which OEMDTC may be compensated”
HEADLINER SAG AT THE CENTER HIGH MOUNTED STOPLAMP – BUILT ON OR BEFORE 9/22/2014 – FLAT ROCK ASSEMBLY PLANT

 

FORD: 2014-2015 Fusion

 

2014-2015 Fusion vehicles built at the Flat Rock assembly plant on or before 9/22/2014 may exhibit a headliner sag by the center high mounted stoplamp.

 

SERVICE PROCEDURE

  1. Check the vehicle identification number (VIN). Does the first position start with a 1?
    1. Yes – proceed to Step 2.
    1. No – this article does not apply, refer to Workshop Manual (WSM) for normal diagnosis.
  1. Release the two D-pillar trim panel clips and the 2-stage D-pillar retention clip. Refer to WSM, Section 501-05 for clip location and 2-stage retention clip release information.
    1. It is not necessary to remove the D-pillar from the C-pillar assembly.
  1. Lower the seat backs of both rear seats. Refer to the seats section of the Owner’s Manual if needed.
  1. Placing both hands around the rear headliner edge, pull down the headliner approximately 7.6 cm (3 in) to release the magnets attaching the headliner to the roof. (Figure 1)
    rear headliner edge
    Figure 1

    1. Pulling the headliner down more than 7.6 cm (3 in) cause damage to the headliner.
  1. Using a flat scraper or knife, remove and discard the rear magnet carriers from the rear of the headliner.
    1. Depending on the vehicle build date there may be no rear magnets, one magnet or 3 magnets securing the headliner to the roof. Remove any rear magnets still stuck to the roof that did not remain glued to the headliner.
  1. Familiarize yourself with the proper placement of the magnets on the vehicle.
    1. Disregard the right and left side markings on the magnet carriers.
    1. Place the passenger side magnet to the metal roof so the cutout portion of the black plastic carrier goes around the outer stoplamp stud on the passenger side. Make sure the thin, white plastic edge of the carrier aligns with the rear metal edge of the roof. (Figure 2)
      white plastic edge of the carrier
      Figure 2
    1. Place the center magnet to the roof so the carrier is centered with the center high mounted stoplamp. Make sure the thin, white plastic edge of the carrier aligns with the rear metal edge of the roof. (Figure 3)
      white plastic edge of the carrier
      Figure 3
    1. Place the driver side magnet to the roof so the cutout portion of the black plastic carrier goes around the outer stoplamp stud on the driver side. Make sure the thin, white plastic edge of the carrier aligns with the rear metal edge of the roof. (Figure 4)
      white plastic edge of the carrier
      Figure 4

 

  1. Place drop cloths, as needed, in the back seat and package tray area of the vehicle.
  1. Remove all 3 magnets and place them magnet side down on a piece of cardboard or shop rag so glue does not get on the interior upholstery during application. Keep the magnets in the same orientation as their placement on the vehicle.
  1. After putting on latex gloves, take the nozzle that comes with the 3M Semi-Rigid Plastic Repair adhesive or equivalent and cut the tip of the nozzle to the largest opening.
  1. The following steps of applying adhesive and attaching the magnets need to occur in less than 50 seconds and require a helper. The person familiar with the placement of the magnets should remain in the back of the vehicle while the helper is within reach applying the glue.
    1. Using 3M Semi-Rigid Plastic Repair adhesive or equivalent, have the helper place a 6 mm (1/4 in.) bead of adhesive around the black plastic edge of each magnet carrier on the opposite side of the magnet. The bead should cover the holes on the black plastic. Once glue starts to come out of the nozzle, do not spend more than 10 seconds applying glue to a single magnet carrier.
    1. As soon as the helper is finished adding adhesive to the back of the first magnet carrier, pull down on the headliner and quickly place the magnet to the roof while the helper starts to place glue on the back of another magnet. Keep the headliner pulled down and continue to quickly place the magnets on the vehicle until all 3 magnets with glue are in place.
    1. Quickly remove the latex gloves so no glue is transferred to the headliner, and push the headliner up to the magnet carriers. Press and hold the headliner in place using the palm of your hand and forearm. Apply firm pressure for 2 minutes.
  1. Replace the D-pillar trim panel 2-stage retention clip and reattach the D-pillar trim panel.

 

Obtain Locally
Part Number Part Description
08190 Headliner Sag by the Center High Mounted Stoplamp - 2014-2015 Ford Fusion | small light 3M Performance Manual Applicator – 50 mL
34240 Headliner Sag by the Center High Mounted Stoplamp - 2014-2015 Ford Fusion | small light 3M Semi-Rigid Plastic Repair – 50 mL

 

PART NUMBER PART NAME
DS7Z-5452124-A Magnet Carrier Kit
W715667-S439 D-Pillar Trim Panel 2-Stage Retention Clip

 

2 thoughts on “Headliner Sag by the Center High Mounted Stoplamp – 2014-2015 Ford Fusion”

Leave a Reply to oemdtc Cancel reply

Share to...