NHTSA ID Number: 10186412
Manufacturer Communication Number: TSB 21-2007
Some 2020 Escape vehicles equipped with a 1.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). To correct the condition, follow the Service Procedure steps to replace the crankcase ventilation tube assembly and reprogram the PCM.
1 Affected Product
TECHNICAL SERVICE BULLETIN
1.5L – Illuminated MIL With DTC P04DB – Built On Or Before 21-Jul-2020
11 January 2021
|Engine: 1.5L EcoBoost|
Issue: Some 2020 Escape vehicles built on or before 21-Jul-2020 and equipped with a 1.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). To correct the condition, follow the Service Procedure steps to replace the crankcase ventilation tube assembly and reprogram the PCM.
Action: Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria:
NOTE: Part quantity refers to the number of that service part number required, which may be different than the number of individual pieces. Service part numbers contain 1 piece unless otherwise stated. “As Needed” indicates the part is required but the number may vary or is not a whole number; parts can be billed out as non-whole numbers, including less than 1.
|Heat Shrink Tubing||1||3U2Z-14A088-BA|
|Coroplast Electrical Wire Harness Tape (Rotunda)||As Needed||NAl837X|
Warranty Status: Eligible under provisions of New Vehicle Limited Warranty (NVLW)/Emissions Warranty/Service Part Warranty (SPW)/Special Service Part (SSP)/Extended Service Plan (ESP) coverage. Limits/policies/prior approvals are not altered by a TSB. NVLW/Emissions Warranty/SPW/SSP/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool.
|2020 Escape 1.5L: Retrieve DTCs Replace The Crankcase Ventilation tube Assembly Includes Time To Remove The Crankcase Pressure Sensor Electrical Connector And Reprogram The PCM (Do Not Use With Any Other Labor Operations)||212007A||0.8 Hrs.|
- Remove and discard the crankcase ventilation Refer to Workshop Manual (WSM), Section 303-08A.
- Cut the crankcase pressure sensor electrical wires approximately 2.5 cm (1 in.) away from the crankcase pressure sensor and discard the hard shell from the harness side.
- Apply heat shrink tubing to cap the ends of the 3 harness side wires.
- Tape the harness wires back to the harness.
- Install the new crankcase ventilation tube using the permanent connection Refer to WSM, Section 303-08A.
- Reprogram the PCM using the latest version of the appropriate Ford diagnostic scan tool.
NOTE: Advise the customer that this vehicle is equipped with an adaptive transmission shift strategy which allows the vehicle’s computer to learn the transmission’s unique parameters and improve shift quality. When the adaptive strategy is reset, the computer will begin a relearning process. This relearning process may result in firmer than normal upshifts and downshifts for several days.
1 Associated Document
11 January 2021
|Diagnostic Software||Interface Device||Complete Vehicle Diagnostics||Module Programming|
|IDS/FDRS||VCM, VCM II, VCMM||X||X||X||X|
|FJDS/FDRS||Compatible J2534 Devices|
(Including VCM II and VCMM)
Detailed system requirements, installation, and support information for each product is located under the diagnostics tool support tab for each product.
For use with VCM I, VCM II, VMM and VCMM hardware devices only. The complete factory Ford Motor Company vehicle diagnostic tool that provides complete dealership level vehicle diagnostic coverage for all 1996 to present Ford, Lincoln and Mercury vehicles. The IDS software includes time based access to the IDS software, software updates and calibration files.
For use with compatible J2534 hardware devices. FJDS software provides Ford Module Programming functionality that covers 1996 to present Ford, Lincoln and Mercury module reprogramming functions, plus complete dealership level vehicle diagnostic software for all 2018 to present Ford and Lincoln vehicles. The FJDS software license includes time based access to the FJDS software, software updates and calibration files.
|CarDAQ-Plus 2 Diagnostic Code Reader and J2534 Programming Tool|
|VSI J2534 ECU Reprogrammer|
|Drew Tech Mongoose Pro USB to CAN ISO9141 Interface|
- [Vehicle Coverage] One device Compatible for Ford and Compatible for Mazda, Support vehicle till 2018 year. (Can't Support Ford F-150 ). Support Automatic Vehicle Recognition.
- [ECU Functions] Programming & Installation of new ECUs (PCM, ABS, Instrument Cluster, Air Bag, Fuel Pumps, etc.). Live Data-stream with Recording & Playback Functions for Main ECUs. New Software Re-flash for Existing ECUs.
- [Functional] Connect via USB. Support Read & Clear Diagnostic Trouble Codes (DTCs); Set, Adjust or Remove Speed Governors; Steering Angle Resets, Guided Fault Finding&All Other Dealer Functions.
- [Update] Update by CD with Unlocked Firmware. ★Please Note: If you have any problem when you install the software, please feel free to contact us, our technology team will provide customers service to help you solve the problem. Multilingual: Support English/German/French/Italian/Spanish/Dutch/Slovenian/Finnish/Danish/Norwegian/Portuguese(European)/Portuguese(Brazil).
- 🚩Firmware support update online. If you have any problem, please fell free contact to us, we will help you fix it by TeamViewer or message support.
- Advanced Diagnostic Scanner for ECU Programming : MK908P has been designed to perform some of the most complicated engine diagnostics and reprogramming in BMW and Mercedes Benz. With the jbox/J2534 VCI or BMW Ethernet Cable, you can edit the cars performance data, like adjusting RPM, fuel injection, etc. A professional car diagnostics scanner to save time/effort on repairs. Form some of the most complicated engine diagnostics and reprogramming in BMW and Mercedes Benz
- Comprehensive Features : Besides Coding and ECU programming functions, the scan tool supports reprogram keys, Bi-directional control, active test, ABS bleeding, complete capabilities for codes, live data, actuation tests, adaptations, prints out recorded data with Wi-Fi. Warm tips Benz-14 & Chang'an-3 Adapters only for UK version, not US version
- User Friendly : The live data stream displayed the real time PID data from ECU and the displayed data included analog inputs and outputs, digital inputs and outputs and system status information broadcast. The graphic display greatly improved the readability and understandability of above parameters. This is definitely a perfect scan tool for enthusiasts interested in knowing how their car is running
- Easy to Operate : The hardware can equal to a best rank android tablet in the market and that made the whole diagnostic procedure more quickly and precisely. Maxisys platform, cloud-based Maxisys provide a large amount of data about the diagnosis and repair advices, that’s really helpful, whenever you encounter problems, you can find solutions from it
- Compatible with Some Add-ons : Combination with Oscilloscope Maxi Scope MP408 and Digital Inspection Cameras MV108, the power of this tool is amazing and the detail you receive about every component of the vehicle makes pinpointing a problem painless. Affordable combination of MS908P and TS601 supports TPMS programming, which turns into a powerful diagnostic tool.
- 👍【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook.com🚘 !
- 👍Fully compatible with both SAE J2534-1 and J2534-2 reprogramming standards and performs standard Pass Thru J2534 functionality. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- 👍Compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- 👍Built-In Wireless with advanced networking functions and data storage. Fast performance ensures quickly reprogramming even the newest controllers & Internet upgradable and updatable.
- 👍Attention: 1. After you ordered and received the J2534, please send us both of the S/N(12 digits, at the back of the device) of the J2534 and your MK908(P) /MS908S (Pro)/ Maxisys Elite to us to bind the two device together. 2. The functions are NOT universally compatible. Please send VIN number to 🚘auteldirect @ outlook . com🚘 to check compatibility before your order.
- OE-Level OBD Scanner: The diagnostic tool serves as the most advanced automotive diagnostic tool, comes with a J2534 ECU programming device that helps Benz and BMW users replace the existing software/firmware in the ECU, program new ECUs and fix software-controlled driving performance and emission issues. Welcom to contact [email protected] or ask through Q&A for your specific need and to ensure the vehicle compatibility
- All-system Diagnose & Active Test: Provided with full-systems diagnosis(ABS, SRS, Engine, Transmission, Brake System, Emission System, Fuel system, Light system, Wiper System, etc.). The diagnostic tool supports bi-direction control to check the vehicle operating conditions. The bi-directional control of the ECM in Component Test enables the MK908P to transmit control commands to operate the vehicle systems
- 30+ Service Functions: As the advanced version of MS908P,MS908S,MS908E, MS908PS PRO, MK908P also offers another 30+ service functions to help your repairing work faster, easier, and more professional, These service functions include immo keys/throttle/injecor coding/trans adaption/suspension/tyre retrofit/DPF/brake bleed/oil reset and more
- Broad Compatibility: The software of MK908P has a wide range of compatibility and can be used to diagnose vehicles from over 80 brands in the US, Europe and Asia. Moreover, you can get more newly added car models with the fast-release software update service. The MaxiFix provides you with an online troubleshooter database, and Remote Desk allows you to get help from others via TeamViewer software
- With TS401 TPMS Relearn Tool: Since MK908P only supports basic detection functions for TPMS, so it is equipped with TS401, a powerful TPMS tire pressure reset tool, which can help you to program a sensor and do the Relearn procedure
- 【XP400 Programmer 】XP400 is to read transponder data (especially Benz infrared smart key), clone and generate exclusive keys, read/write on-board EEPROM data, etc. IMMO application provides Smart Mode and Expert Mode to guide technicians performing IMMO related functions, including Key Learning, Remote Control Learning, Remote Control Add, etc. Please send VIN number to▲Autelonline @ outlook . com▲ to check compatibility before purchasing.
- 【KEY PROGRAMMING Function】The most advanced and smart key programming tool that combines the most powerful IMMO and programming functions with OE-level diagnostics and advanced service functions in one Android based 10.1-inch touchscreen tablet, it helps perform complete key programming quickly.
- 【IMMO & J2534 Reprogrammer】The Wireless Diagnostic Interface supports two communication methods with the tablet: BT and USB. The working range for BT communication is about 210 feet (70 m). You can perform key programming and vehicle diagnosis on various vehicles conveniently, by pairing the tablet separately to each of the MaxiFlash.【 Note: J2534 can't program ECU with the IM608】
- 【ECU CODING & ACTIVE TEST & 23 Services Function】Bi-directional control of the ECM is useful in determining whetherthe ECM responds to a command well. And Auto VIN Identification, ECU Coding are available for IM608. Most useful service including: Oil Reset Service/ EPB Service/ BMS Service/ SAS Service/ DPF Service etc.
- 【No IP Lock & 1 Year Free Update + Life-long time tech-support】More langauage are available such as French, German, Italian, Polish, Dutch, Swedish, Korean, Japanese, Russian. Please contact by providing SN if needing authorized.
- VCX is designed on the basis of the latest automotive international standards so that it can support many professional automotive diagnostic applications
- VXDIAG VCX Nano support latest version software, Compatible with varieties protocols. can be very easy to connect various automotive bus to a PC
- OS support Windows 7, Software support multi-languages: Chinese, English, French, Italian, Spanish, German, ec
- Please download the latest vxmanager from vxdiag official website. Use new vxmanager to update firmware and driver and then update your device authorization.
- We provide full time online support, if you have any questions about our device, please feel free to contact us online via ask us a question or send us email
- Designed for CV ➤ Autel MaxiSys MS908CV boasts the pro-level diagnostics for Commercial Vehicles (Expert, Buses & Trucks), to get all module access for ECU Coding, Active Test (Bi-directional Control), 23 Adaptation Services, 25 Service Functions, Read/Erase Codes and Live Data, etc., being compatible with multiple supported protocols: SAE J1939, SAEJ1708, Manufacture-defined protocol J1939, Manufacture-defined J1708, KWP, VPW, UDS-CAN, CDL.
- ECU Coding ➤ This Heavy Duty diagnostic tool allows you to re-flash the commercial vehicles’ control modules, and write in adaptive data for certain components after making repairs or replacements, to fix the issues as: Drivability, Fuel Efficiency, Power Loss, Fault Codes, Durability of Mechanical Parts, etc. (Note: Coding only changes preprogrammed options already existent in the software.)
- 23 Adaption Functions ➤ This commercial vehicle scanner provides various 23 component adaptation services, to calibrate or reset certain components after repair or replacement as: DOC/DPF Instant Replacement Reset, Fuel Pressure Adaptation Accurate Reset, After Treatment Maintenance, Calibration of Rack Sensor, Calibration of Injector Trim, and others, with fast navigation for optimal efficiency.
- 25 Service Functions ➤ This automotive diagnostic tool can Read/Clear codes, view graphic Live Data, and features an array of 25 guided maintenance services as: Oil Reset, Injector Coding, DPF, EPB, ABS/SRS, Suspension, Throttle, Odometer, Lang Change, Headlamp, CHG Tire Size, Airbag Reset, Cylinder, Turbocharging, Limit, Clutch, WIN DR ROOF, TEC Learn, Trans Adaption, Immo Keys, TPMS, BMS, Brake Bleed, Seats etc.
- Ultimate Scanner ➤ Autel MS908CV gives you all necessary functionalities, while still remaining easy to use with boosted multitasking performance: Android 4.0 operating system, Quad-Core Processor, 2GM RAM & 32GB SSD, 9.7" 1024*768 IPS Screen, 11000 mAh Battery (8hrs non-stop operation), 5.0M AF Rear Camera, etc..This scanner is entitled to 1-year warranty with 1-year FREE software update. Welcome to contact us for your vehicle’s compatibility check, 24/7.
- 【ADVANCED ECU PROGRAMMING】 This pro-level scan tool features Autel’s Powerful Complete Diagnostic System with easy-to-go workflow of ECU Coding: / for customer individual customization of the car (to improve vehicle performance, or stimulate high-end car functions); / for the configuration alteration (when a component is replaced); / and for multiple car systems’ recognition of each other etc. , with optimal efficiency.
- 【36+ SERVICE FUNCTIONS】This OE-Level diagnostic scanner offers more than 36 service functions as Oil Reset, Injector Coding, EPB, TPMS, BMS, Brake Bleed, DPF, Immo Keys, SAS, Suspension, Throttle etc. It also gains full access of all available vehicle modules to Retrieve ECU information, Read & Erase DTCs, and View Live Data of each parameter item, with Bi-Directional Control (Active Test) to check the operating conditions of various car systems and components.
- 【J2534 PROGRAMMING】Autel MaxiSys Elite features J2534 ECU Programming for BMW & Benz, to access, update, replace and program the existing software/firmware in ECUs, without the need of a dealer-only tool, to troubleshoot and deal with complex vehicle problems like Driveability, Fuel Efficiency, Power Loss, Fault Codes, and Durability of mechanical parts etc. , with easy step-by-step instructions. This ultimate Autel scanner is made for perfection.
- 【DISCOVER OUR 24/7】2 years FREE software update + 1 year . This diagnostic tool is backed by Autel’s professional tech team and service team, to offer the top quality product and service in the industry. Autel MaxiSys Elite comes a way in easing up and increasing efficiency in your professional diagnostics from all the features mentioned above. The returns are a . *The tool is only available to sell in the U. S. Region.
- 【STATE-OF-THE-ART HARDWARE】This Android 4. 4. 4 KitKat OS-based, tablet-style diagnostic scanner incorporates the world’s fastest mobile processor NVIDIA’s Tegra 4, with internal 2GB RAM (32GB SSD), for boosted performance (boot-up time < 20 sec). Also, Elite comes with a visually stunning sharp Retina display of 9. 7”, with an 8. 0-megapixel rear camera with flashlight and auto focus. This scan tool is bound to work as fast and effective as possible.
- VXDIAG VCX 2 in 1 works for both Ford and Mazda, support Ford and Mazda Diagnose and Programming.(Please download the latest vxmanager from vxdiag official website. Use new vxmanager to update firmware and driver and then update your device authorization.)
- Worth to own: Support J2534 protocol, this device actually works faster than Obdlink MX and ELM327 devices with Forscan, it can also works with FJDS license for programming. This is a great alternative to buying an expensive VCM2 for programming modules
- Support vehicle till 2019 year（Not works for FORD F150,F250,F350,F450,F550,F650,F750 before 2010）,Support Multi-Languages
- VXDIAG VCX NANO is an OEM diagnostic interface for the vehicles of Ford and Mazda. It can be compatible with OEM software of Ford IDS and Mazda IDS
- Full Technical Support Online: Firmware support update online. For software installation, you can feel free to contact us via amazon message, our engineer will provide online support by teamviewer or video
- 🚗【2021 Newest. Key Programming + IMMO Function】The most advanced and smart key programming tool that combines the most powerful IMMO and programming functions with OE-level diagnostics and advanced service functions in one Android based 10.1-inch touchscreen tablet, it helps perform complete key programming quickly. Please send VIN to⭐Autelonline @ outlook . com⭐ to check compatibility.
- 🚗【Advanced XP400 Programmer】XP400 is to read transponder data (especially Benz infrared smart key), clone and generate exclusive keys, read/write on-board EEPROM data, etc. IMMO application provides Smart Mode and Expert Mode to guide technicians performing IMMO related functions, including Key Learning, Remote Control Learning, Remote Control Add, etc
- 🚗【ADVANCED IMMO + J2534 ECU programmer】Immobilizer is also known as immo box which is to auto part that recognizes the vehicle key directly. MaxiFlash specially designed to provide users with convenient PC communication on any modern vehicle diagnostic, and offer the most significant features desired by OEM customers: reliability, fast performance and flexibility. The working range for BT communication is about 210 feet (70 m). ▲The J2534 Can't Program ECU With IM608▲
- 🚗【ACTIVE TEST + ECU CODING + 30+ RESET SERVICE】Bi-directional control of the ECM is useful in determining whetherthe ECM responds to a command well. And Auto VIN Identification, ECU Coding are available for IM608. Most useful service including: Oil Reset Service/ EPB Service/ BMS Service/ SAS Service/ DPF Service etc.Powerful OE level diagnostics for more than 80 US, Asian and European makes and models.
- 🚗【(US ONLY) 1 YEAR FREE UPDATE + PERMANENT After-Sales SERVICE】▲IM608 just can be used in US. Please don't switch the IP or the device will be locked! IM608 comes with 1 Year free updates.
Last update on 2021-03-06 / Affiliate links / Images from Amazon Product Advertising API
Last update on 2021-03-06 / Affiliate links / Images from Amazon Product Advertising API