14S22 – Fuel Tank Corrosion Inspection and Repair – 2007-2008 Ford & Lincoln

“This site contains affiliate links for which OEMDTC may be compensated”

NHTSA

14V682

SUMMARY:

Ford Motor Company (Ford) is recalling certain model year 2007-2008 Lincoln MKX, and Ford Edge vehicles, manufactured June 15, 2006, to September 22, 2008, and originally sold, or currently registered in, Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia.

 

CONSEQUENCE:

A fuel leak in the presence of an ignition source increases the risk of a fire.

 

REMEDY:

Interim notices were mailed to owners on December 12, 2014.

The recall began on October 6, 2015.

Dealers will inspect the vehicles and either clean and treat the fuel tank with a corrosion preventative or replace the tank, free of charge.

Owners may contact Ford customer service at 1-866-436-7332.

Ford’s number for this recall is 14S22.

 

NOTES:

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your Vehicle has a Recall

 


April 28, 2016

TO: All U.S. Ford and Lincoln Dealers

SUBJECT: Safety Recall 14S22 Supplement #3
Certain 2007 and 2008 Model Year Edge and MKX Vehicles Operated in Corrosion States
Fuel Tank Corrosion Inspection and Repair

REF : Regional Program 14R02 – Supplement #1
Dated April 28, 2016

 

REASON FOR THIS SUPPLEMENT

Field data gathering:  Sufficient field data has been collected.  Images of corroded fuel tanks no longer need to be submitted for review.  Repairs dated May 5, 2016, and later that include labor operation 14S22D for SSSC Image Submission will not be accepted.

 

AFFECTED VEHICLES

Certain 2007 and 2008 model year Edge and MKX vehicles built at the Oakville Assembly Plant from June 15, 2006 through September 22, 2008 and originally sold in, or currently registered in the following states:

Connecticut Iowa Michigan New York West Virginia
Delaware Kentucky Minnesota Ohio Wisconsin
District of Columbia Maine Missouri Pennsylvania
Illinois Maryland New Hampshire Rhode Island
Indiana Massachusetts New Jersey Vermont

 

Affected vehicles are identified in OASIS.  In addition, for a list of vehicles assigned to your dealership, visit https://web.fsavinlists.dealerconnection.com.   

NOTE:  A separate Customer Satisfaction Program (14R02), covering inspections and repairs on affected vehicles located outside of the above listed corrosion states, was released December 15, 2015.

 

REASON FOR THIS SAFETY RECALL

In some of the affected vehicles that are operated in high-corrosion environments associated with road salt use, moisture and salt may become trapped under the fuel tank mounting reinforcement brackets at the four corners where the fuel tank is attached to the vehicle.  Over time, corrosion under these reinforcement brackets can spread to the fuel tank which can result in a fuel leak.  A fuel leak in the presence of an ignition source may result in a fire.      

SERVICE ACTION

Dealers are to remove and inspect the fuel tank for corrosion. Based on the results of the inspection, dealers will either clean and treat or replace the fuel tank.  This service must be performed at no charge to the vehicle owner.

 

OWNER NOTIFICATION MAILING SCHEDULE

Original owner letters were mailed in December 2014.  Phased follow-up notifications completed mailing the week of April 18, 2016.  Dealers should repair any affected vehicles that arrive at their dealerships, whether or not the customer has received a letter.

 

ATTACHMENTS

Attachment I: Administrative Information
Attachment II: Labor Allowances and Parts Ordering Information
Attachment III: Technical Information
Owner Notification Letters
Recall Reimbursement Plan

 

QUESTIONS & ASSISTANCE

For questions and assistance, contact the Special Service Support Center (SSSC) via the SSSC Web Contact Site.  The SSSC Web Contact Site can be accessed through the Professional Technician Society (PTS) website using the SSSC link listed at the bottom of the OASIS VIN report screen or listed under the SSSC tab.


ATTACHMENT I

Safety Recall 14S22 – Supplement #3
Certain 2007 and 2008 Model Year Edge and MKX Vehicles Operated in Corrosion States
Fuel Tank Corrosion Inspection and Repair

 

OASIS ACTIVATED?

Yes, OASIS was activated on October 28, 2014.

 

FSA VIN LIST ACTIVATED?

Yes, FSA VIN list is available through https://web.fsavinlists.dealerconnection.com.  Owner names and addresses will be available by October 5, 2015.  

NOTE:  Your FSA VIN list may contain owner names and addresses obtained from motor vehicle registration records.  The use of such motor vehicle registration data for any purpose other than in connection with this program is a violation of law in several states, provinces, and countries.  Accordingly, you must limit the use of this listing to the follow-up necessary to complete this service action.

 

STOCK VEHICLES

Use OASIS to identify any affected vehicles in your used vehicle inventory.

 

SOLD VEHICLES

  • Owners of affected vehicles will be directed to dealers for repairs.
  • Immediately contact any of your affected customers whose vehicles are not on your VIN list but are identified in OASIS. Give the customer a copy of the Owner Notification and schedule a service date.
  • Correct other affected vehicles identified in OASIS which are brought to your dealership.  

 

TITLE BRANDED / SALVAGED VEHICLES

Affected title branded and salvaged vehicles are eligible for this recall.

 

ADDITIONAL LABOR TIME AND/OR PARTS

Submit a request to the SSSC Web Contact Site prior to the repair if you have any of the following:

  • Damage that you believe was caused by the covered condition.
  • A condition that requires additional labor and/or parts to complete the repair. For repairs where additional time is needed due to difficulty removing fuel tank bolts, etc., dealers are authorized to claim up to 2.0 hours actual time without contacting the SSSC Web Contact Site for approval.  Follow the Actual Time Usage Guidelines and Service Management Responsibilities as identified in the Warranty and Policy Manual.  Claims for additional parts or labor over 2.0 hours should be submitted to the SSSC as a Related Damage contact.
  • Aftermarket equipment or non-Ford modifications to the vehicle which might prevent the inspection of the covered condition.

Requests for approval after completion of the repair may not be granted.  Ford Motor Company reserves the right to deny coverage for related damage in cases where the vehicle owner has not had this recall performed on a timely basis.  Additional related damage parts are subject to random selection for return to the Ford Warranty Parts Analysis Center (WPAC).

 

OWNER REFUNDS

  • This safety recall must still be performed, even if the owner has paid for a previous repair. Claiming a refund will not close the recall on the vehicle. 
  • Ford Motor Company is offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which is posted with this bulletin. Owners are directed to seek reimbursement through authorized dealers or, at their option, directly through Ford Motor Company at P.O. Box 6251, Dearborn, MI 481216251.
  • Dealers are also pre-approved to refund owner-paid emergency repairs that were performed away from an authorized servicing dealer after the end date specified in the reimbursement plan. Non-covered repairs, or those judged by Ford to be excessive, will not be reimbursed.
  • Refunds will only be provided for the cost associated with repair or replacement of the fuel tank due to a leak caused by corrosion.

 

RENTAL VEHICLES

If a customer’s vehicle requires replacement of the fuel tank and it is necessary to order parts, dealers are authorized to provide the customers up to five days of vehicle rental.  The daily rate can include applicable taxes but must not exceed $55.00.  Rentals will only be reimbursed for the day(s) the vehicle is at the dealership for part replacement.  Prior approval for more than five rental days is required from the SSSC via the SSSC Web Contact Site.

NOTE:  Any vehicles that were previously grounded due to a verified fuel tank leak should now be repaired and returned to customers, and any long term rental vehicles returned.  Any remaining claims for long term rentals, towing or owner alternate transportation using Program Code 14Y02 must be submitted by October 31, 2015 to be eligible for payment.

 

RENTAL TRACKING AND ALLOWANCE

The administrative allowance for assisting customers with arranging a rental vehicle is no longer available.  Vehicles that require a fuel tank should be repaired at this time.

 

CLAIMS PREPARATION AND SUBMISSION

  • Enter claims using Direct Warranty Entry (DWE) or One Warranty Solution (OWS).
    • DWE: refer to ACESII manual for claims preparation and submission information.
    • OWS: when entering claims in DMS software, select claim type 31: Field Service Action. The FSA number (14S22) is the sub code.
  • Dealers are authorized to claim up to 2.0 hours of additional time without contacting the SSSC for approval. Follow the Actual Time Usage Guidelines and Service Management Responsibilities as identified in the Warranty and Policy Manual.
  • Additional labor and/or parts must be claimed as related damage on a repair line that is separate from the repair line on which the FSA is claimed. Additional labor and/or parts require prior approval from the SSSC via the SSSC Web Contact Site.
  • Claim up to $55.00 per day for customer rental vehicles. Enter the total amount of the rental expense under Miscellaneous Expense code “Rental”.
  • Submit refunds on a separate repair line.
    • Program Code:  14S22           –  Misc. Expense:  ADMIN
    • Misc. Expense:  REFUND     –  Misc. Expense:  0.2 Hrs.
  • Multiple refunds should be submitted on one repair line and the invoice details for each repair should be detailed in the comments section of the claim.
  • Provision for Locally Obtained Supplies: Valugard VG-101A rust inhibitor aerosol or Daubert NOX RUST 7703-W aerosol.  Submit on the same line as the repair.
    • Program Code: 14S22 o Expense: OTHER
    • Expense: Claim up to $8.00

ATTACHMENT II

Safety Recall 14S22 – Supplement #3
Certain 2007 and 2008 Model Year Edge and MKX Vehicles Operated in Corrosion States
Fuel Tank Corrosion Inspection and Repair

 

LABOR ALLOWANCES

Description Vehicle Type Labor Operation Labor Time
Remove, Clean, and Treat Fuel Tank Includes inspection (pass). FWD vehicles 14S22B 1.7 Hours
Remove, Clean, and Treat Fuel Tank Includes inspection (pass). AWD vehicles 2.0 Hours
Remove and Replace Fuel Tank

Includes inspection (fail) and transfer of parts.

FWD vehicles 14S22C 1.6 Hours
Remove and Replace Fuel Tank

Includes inspection (fail) and transfer of parts.

AWD vehicles 2.0 Hours

 

PARTS REQUIREMENTS / ORDERING INFORMATION

To manage the initial flow of fuel tank shipments, a seed stock distribution to dealers in corrosion areas will be administered over the course of five to six weeks, beginning the week of Sep 21, 2015.  The seed stock plan will target approximately 10% of the estimated volume of fuel tanks needed by each dealer for this recall.  The fasteners and seals needed for fuel tank replacement will be shipped separately from the fuel tanks during the seed stock program.  Parts departments are encouraged to manage their inventory accordingly.

Dealer affected vehicles Seed Stock Expectation
Fewer than five FWD vehicles None
Fewer than five AWD vehicles None
Five or more FWD vehicles At least one AT4Z-9002-DCP fuel tank plus associated hardware and other parts needed to replace the fuel tank.

(Actual volume of seed depends on the number of affected vehicles assigned to the dealer)

Five or more AWD vehicles At least one AT4Z-9002-CCP fuel tank plus associated hardware and other parts needed to replace the fuel tank.

(Actual volume of seed depends on the number of affected vehicles assigned to the dealer)

 

Dealers can access https://web.fsavinlists.dealerconnection.com to identify the total number of affected vehicles assigned to their dealership in order to help determine if they will receive parts under the seed stock plan.  Dealers that do not receive parts under the seed stock plan and need a fuel tank prior to open ordering should submit a Part Order contact using the SSSC link at the bottom of the OASIS VIN report screen.  Images of the failed fuel tank should be attached to the Part Order contact.

NOTE:  Dealers that want to discontinue their participation in the seed stock plan should submit a General contact request to the SSSC via the web link on the PTS site.  Please note that removing a dealer from this seed stock program is a permanent action and dealers will not be re-entered into the seed plan.  

 

Part Number Part Name Order Quantity
FWD vehicles
AT4Z-9002-DCP Fuel tank assembly (replace only if inspection failed) 1
4L3Z-9276-AA 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Fuel pump o-ring (replace only if inspection failed) 1
W713928-S438 Fuel tank bolts (4/package, 4 needed) 1
W506023-S439 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Fuel tank to bracket bolts (4/package, 4 needed) 1
AWD vehicles
AT4Z-9002-CCP 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Fuel tank assembly (replace only if inspection failed) 1
4L3Z-9276-AA 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Fuel pump o-ring (replace only if inspection failed) 1
W713928-S438 Fuel tank bolts (4/package, 4 needed) 1
W506023-S439 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Fuel tank to bracket bolts (4/package, 4 needed) 1
W711918-S439eBay Rear driveshaft flange bolts (4/package, 4 needed) 1
W520113-S440 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Driveshaft center support bearing nuts (4/package, 4 needed) 1
Additional materials for fuel tank anti-corrosion treatment
VG-101A Valugard rust inhibitor aerosol (obtain from www.valugard.net) Claim anticorrosion

treatment as

MISC OTHER

7703-W 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Daubert NOX RUST aerosol (obtain from www.daubertchemical.com)
PM-4-A 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light Motorcraft metal brake parts cleaner (or equivalent) 1
PM-4-B 14S22 - Fuel Tank Corrosion Inspection and Repair - 2007-2008 Ford & Lincoln | small light

 

The DOR/COR number for this recall is 50566.   

Order your parts through normal order processing channels.

 

DEALER PRICE  

For latest prices, refer to DOES II.

 

PARTS RETENTION AND RETURN

Follow the provisions of the Warranty and Policy Manual, Section 1 “WARRANTY PARTS RETENTION AND RETURN POLICIES.”

 

EXCESS STOCK RETURN

Excess stock returned for credit must have been purchased from Ford Customer Service Division in accordance with Policy Procedure Bulletin 4000.


ATTACHMENT III

 

CERTAIN 2007 THROUGH 2008 MODEL YEAR EDGE AND MKX VEHICLES — FUEL TANK CORROSION INSPECTION AND REPAIR

 

OVERVIEW

In some of the affected vehicles that are operated in high-corrosion environments associated with road salt use, moisture and salt may become trapped under the fuel tank mounting reinforcement brackets at the four corners where the fuel tank is attached to the vehicle. Over time, corrosion under these reinforcement brackets can spread to the fuel tank which can result in a fuel leak. A fuel leak in the presence of an ignition source may result in a fire.

 

SERVICE PROCEDURE

WARNING: do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.

WARNING: do not carry personal electronic devices such as cell phones, pagers or audio equipment of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.

WARNING: Before working on or disconnecting any of the fuel tubes or fuel system components, relieve the fuel system pressure to prevent accidental spraying of fuel. Fuel in the fuel system remains under high pressure, even when the engine is not running. Failure to follow this instruction may result in serious personal injury.

WARNING: Remove the fuel filler cap slowly. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out. Failure to follow these instructions may result in serious personal injury.

WARNING: When handling fuel, always observe fuel handling precautions and be prepared in the event of fuel spillage. Spilled fuel may be ignited by hot vehicle components or other ignition sources. Failure to follow these instructions may result in serious personal injury.

 

Fuel Tank Removal Procedure

All Vehicles

  1. Position vehicle on a hoist. Please follow Workshop Manual (WSM) procedures in Section 100-02.
  2. Check fuel level indication on instrument cluster and drain fuel if needed.
    • If less than 1/2 tank, it is not necessary to drain fuel. Continue to Step 3.
    • If more than 1/2 tank, drain fuel to attain less than 1/2 tank as follows:
      1. Remove fuel tank filler cap and position it aside.
      2. Insert a suitable fuel drain tube into the fuel tank filler pipe until it enters the fuel tank.
      3. Attach a fuel storage tanker to the drain tube and drain fuel to bring fuel level below 1/2 tank.
  1. Release the fuel system pressure. Please follow WSM procedures in Section 310-00.
  2. Disconnect the battery ground cable. Please follow WSM procedures in Section 414-01.
  3. Lower or remove the muffler and tailpipe as follows:

NOTE: Do not damage or tear the isolators during removal. Do not use oil or grease-based lubricants on the isolators. They may cause deterioration of the rubber. Use soapy water as needed to separate the isolators from the vehicle.

 

Front Wheel drive (FWD) Vehicles

  1. Detach the three (3) muffler and tailpipe assembly rear isolators. See Figure 1.
  2. Position the rear of the exhaust system down approximately 305 mm (12 in) and support using a jack stand.

rear of the exhaust systemFIGURE 1

 

All Wheel drive (AWD) Vehicles

  1. Detach the four (4) muffler and tailpipe assembly isolators. See Figure 2.
  2. Loosen the Torca clamp and remove the exhaust system from the vehicle.

NOTE: Install a new Torca clamp, if necessary, following the procedures in Section 309-00.

Torca clampFIGURE 2

 

  1. With the help of an assistant, detach and position the rear of the driveshaft aside as follows: See Figure 3.
    1. Remove and discard the four (4) rear u-joint flange bolts at the differential assembly.
    2. Remove and discard the two (2) or four (4) center bearing support nuts. Position and secure the driveshaft up and to the left side of the vehicle.

center bearing support nutsFIGURE 3

 

All Vehicles

  1. Install a suitable lifting device under the fuel tank.
  2. Disconnect the fuel tank wiring harness electrical connector.
  3. Disconnect the Fuel Tank Pressure (FTP) sensor electrical connector.
  4. Disconnect the fuel vapor tube assembly-to-fuel tank quick connect coupling. Please follow WSM procedures in Section 310-00.
  5. Release the clamp and disconnect the fuel tank filler pipe hose from the fuel tank.
  6. Disconnect the fuel tank jumper tube-to-fuel tube quick connect coupling. Please follow WSM procedures in Section 310-00.
  7. Remove the two (2) parking brake cable bracket bolts and position cables aside.

NOTICE: Position the lifting device securely against the fuel tank prior to loosening any fuel tank attaching bolts.

  1. Remove the fuel tank bolts as follows:
    1. Remove and discard two (2) bolts attaching the fuel tank to the fuel tank brackets at both the front center and rear center of the tank (four (4) bolts total). Leave the brackets attached to the vehicle. See Figure 4.
    2. Remove and discard the four (4) bolts (one at each corner) attaching the fuel tank to the body.

NOTE: Two (2) rear center fuel tank to bracket bolts shown, two (2) front center fuel tank to bracket bolts similar.

rear center fuel tank to bracket boltsFIGURE 4

 

NOTE: AWD vehicles require the fuel tank to be positioned forward, past the Rear Differential Unit (RDU), then lowered. FWD vehicles require the fuel tank be partially lowered onto a 102 mm (4 in) by 102 mm (4 in) piece of lumber (or equivalent) placed under the right side of the tank and then lifted and lowered over the exhaust and out the drivers side of the vehicle.

  1. Remove the fuel tank. Continue to Fuel Tank Inspection Procedure on Page 6.

NOTE: If you experience difficulty removing fuel tank corner attaching bolts, it may be necessary to safely heat the bolts during removal. If necessary, use the following procedure.

WARNING: Only use Mini-ductor or equivalent heating device if there is no visible fuel leak and no fuel smell that could be the result of a fuel leak. do not allow the temperature of the bolt to rise above 165°C (330°F).

    1. Using a Mini-Ductor or equivalent and infrared thermometer, heat the corner attaching bolts one at a time to approximately 160°C (320°F). See Figure 5.
    2. Use an air impact gun to remove each bolt immediately after it is heated.

Mini-DuctorFIGURE 5

 

Fuel Tank Inspection Procedure

  1. Inspect the bottom side of the fuel tank for a “FoMoCo” part number stamping. See Figure 6.
    • If the fuel tank has a “FoMoCo” part number stamping, proceed to Step 2.
    • If the fuel tank does not have a “FoMoCo” part number stamping, replace the fuel tank.

bottom side of the fuel tankFIGURE 6

 

  1. If necessary, use a stiff nylon brush and Motorcraft Metal Brake Parts Cleaner to clean any heavy deposits of dirt/debris from around the top center flange area of the fuel tank so the metal in the corner bracket areas can be inspected for rust/corrosion. See Figure 7.

NOTE: DO NOT use a metal or wire brush or scraper. This will compromise the coatings on the tank.

  1. Inspect the fuel tank corner bracket areas, fuel filler and vent tube attachment areas and other areas of the fuel tank for signs of leaks or corrosion. See Figures 7, 8a-8b, and 9a-9b.

fuel tank corner bracket areasFIGURE 7

 

A fuel tank PASSES the inspection procedure if there are no signs of leaks, soft/bubbling paint or corrosion at the edges of the corner brackets, fuel filler and vent tube attachment areas, or other areas of the fuel tank. If the fuel tank passes the inspection, continue to Fuel Tank Corrosion Treatment Procedure on the next page. See Figures 8a and 8b.

fuel tank PASSES the inspection procedure

FIGURE 8a          FIGURE 8b

 

Conditions that indicate a fuel tank FAILS and must be replaced include:

  • Any soft or bubbling paint that is easily scraped from the surface of the tank at ANY location.
  • Any corrosion stemming from below the corner brackets that has compromised the surface of the metal.
  • Excessive corrosion at the weld seam around the top center flange of the tank, at the base of the fuel inlet and vent ports, and on top of the tank at the baffle spot welds.

If the fuel tank fails the inspection, replace the tank and proceed to Fuel Tank Installation Procedure on Page 11. See Figures 9a and 9b.

fuel tank FAILS

FIGURE 9a         FIGURE 9b

 

Fuel Tank Corrosion Treatment Procedure

  1. Using a stiff nylon brush and Motorcraft Metal Brake Parts Cleaner, clean the top surface area of all four (4) corner brackets and surrounding area of the center tank flange.

NOTE: DO NOT use a metal or wire brush or scraper. This will compromise the coatings on the tank.

  1. Clean the area around the fuel fill and vent tubes.
  2. Clean the spot welds on top of the tank.
  3. Wipe clean with shop towel.
  4. Spray Motorcraft Metal Brake Parts Cleaner under each of the corner brackets using the supplied aerosol spray tube. See Figure 10a.
  5. Use compressed air regulated to approximately 137 kpa (20 psi) to spray under the corner brackets to clean/dry the surfaces under them. See Figure 10b.

corner brackets

FIGURE 10a              FIGURE 10b

 

  1. Spray anti-corrosion treatment under each corner bracket using the supplied aerosol spray tube. See Figure 11a.
  2. Use compressed air regulated to approximately 137 kpa (20 psi) to force the anti-corrosion treatment under each of the corner brackets. See Figure 11b.

corner brackets

FIGURE 11a             FIGURE 11b

 

  1. Repeat spraying a second application of anti-corrosion treatment under each of the corner brackets but DO NOT use compressed air on the second application.

NOTE: Before applying anti-corrosion treatment to the fuel tank surface, cover the filler neck and vent tube with a suitable cover to keep these areas free of the treatment. See Figure 12a.

  1. Remove the aerosol tube and apply a heavy coat of anti-corrosion treatment over the following areas of the fuel tank: See Figures 7 and 12a-12d.
    1. Around the fill and vent tubes.
    2. All spot welds on top of the tank.
    3. Corner bracket areas.
    4. On the top center flange around the entire perimeter of the tank.

fill and vent tubes

FIGURE 12a            FIGURE 12b

 

Corner bracket areas

FIGURE 12c             FIGURE 12d

 

  1. Reinstall the fuel tank per the Fuel Tank Installation Procedure on Page 11.

 

Fuel Tank Installation Procedure

All Vehicles

NOTE: If replacing the fuel tank, images of the areas of the tank which fail inspection must be submitted to the Special Service Support Center via the SSSC Web Contact Site. This is not a prior approval process, and images may be submitted at any time during or after the repair process (but prior to warranty claim submission). Retain the ContactID from the SSSC contact and include it in the comments section when submitting the claim.

NOTE: If installing a new fuel tank, the fuel pump module and the fuel level sensor (AWD) must be transferred to the new fuel tank (lubricate the fuel level sensor seal with clean oil to aid in sensor installation), following the procedures in Section 310-01.

  1. Using a suitable lifting device, raise the fuel tank into position.
  2. Install the four (4) new fuel tank bolts (one at each corner).
    • Tighten to 25 Nm (18 lb-ft).

NOTE: The brackets may need to be loosened slightly to reposition them if the center bracket to tank attaching holes do not line up. If necessary, safely heat the bolts using the procedure on page 5.

  1. Install the four (4) new fuel tank to bracket bolts. See Figure 4.
    • Tighten to 25 Nm (18 lb-ft).
  2. Position the parking brake cables and install the two (2) parking brake cable bracket bolts.
    • Tighten to 23 Nm (17 lb-ft).
  3. Connect the fuel tank jumper tube-to-fuel tank quick connect coupling. Please follow WSM procedures in Section 310-00.
  4. Connect the fuel tank pressure sensor.
  5. Connect the fuel tank wiring harness connector.

 

FWD Vehicles

  1. Attach the three (3) muffler and tailpipe assembly isolators. See Figure 1.

 

AWD Vehicles

  1. Position the driveshaft and install the two (2) or four (4) new center bearing support nuts. See Figure 3.
    • Tighten to 40 Nm (30 lb-ft).
  2. Position the driveshaft and install the four (4) new rear u-joint flange bolts. See Figure 3.
    • Tighten to 70 Nm (52 lb-ft).

NOTE: Install a new Torca clamp, if necessary, following WSM procedures in Section 309-00.

  1. Install the muffler and tailpipe assembly and attach the four (4) isolators. See Figure 2.

 

All Vehicles

  1. Connect the battery ground cable. Please follow WSM procedures in Section 414-01.

 

Ford Motor Company
Recall Reimbursement Plan for 14S22

 

Ford and Lincoln Motor Company dealers are in the best position to quickly and efficiently process reimbursement requests.  However, federal legislation requires all motor vehicle manufacturers to establish processes through which customers may seek recall reimbursement directly from the manufacturer or from the dealers. 

Regarding the specific reimbursement plan for Recall # 14S22, owners who have paid for service to remedy the defect or noncompliance must have had that service performed prior to December 22, 2014. After this date, if repairs related to this recall are performed by a non-Ford repair facility in an emergency situation, customers must submit any refund requests through their dealership. As required by this federal regulation, Ford Motor Company submitted the details of its latest General Recall Reimbursement Plan in a letter to the National Highway Traffic Safety Administration (NHTSA) in February 2009.  The following is the text of that letter and the Plan:

 

General Recall Reimbursement Plan
(As submitted to the NHTSA)

Pursuant to the requirements set forth in 49 CFR Part 573 and Part 577 of the Code of Federal Regulations, Ford Motor Company (Ford) is submitting required information pertaining to our general reimbursement plan for the cost of remedies paid for by vehicle owners before they are notified of a related safety recall.

Set forth below is Ford’s general plan to reimburse owners and purchasers for costs incurred for remedies in advance of notification of potential safely-related defects or noncompliances pursuant to Part 573.6 (c)(8)(i).  This plan has not changed since our February 28, 2007 submission.

 

Reimbursement Notification

Ford’s notice to a vehicle owner in accordance with 49 CFR Part 577 will indicate that Ford is offering a refund if the owner paid to have service to remedy the defect or noncompliance prior to a specified ending date.  In accordance with Part 573.13 (c)(2), this ending date will be defined as a minimum of ten calendar days after the date on which Ford mailed the last of its Part 577 notifications to owners, and will be indicated in the specific reimbursement plan available to owners for an individual recall.  This notice will direct owners to seek eligible reimbursement through authorized dealers or, at their option, directly through Ford at the following address:

 

Ford Motor Company
P.O. Box 6251
Dearborn, MI  48121-6251

 

Ford notes that this rule allows for the identification of a beginning date for reimbursement eligibility.  Under the rule, an owner who paid to remedy the defect or noncompliance prior to the identified beginning date would not be eligible for reimbursement.  Ford generally has not established such a beginning date for reimbursement eligibility and does not presently anticipate changing this general policy.  However, in any case where Ford determines a beginning date is appropriate, Ford will indicate that date in the owner notice.  As permitted by 577.11(e), Ford may not include a reimbursement notification when all vehicles are well within the warranty period, subject to approval by the agency.

 

Costs to be Reimbursed

For vehicles, reimbursement will not be less than the lesser of:

  • The amount paid by the owner for the remedy that specifically addressed and was reasonably necessary to correct the defect or noncompliance that is the subject of the recall, or
  • The cost of parts for the remedy (to be no more than the manufacturer’s list retail price for authorized part(s), plus associated labor at local labor rates, miscellaneous fees (such as disposal of waste) and taxes.

For replacement equipment, reimbursement will be the amount paid by the owner for the replacement item (limited by the amount of the retail list price of the defective or noncompliant item that was replaced, plus taxes, where the brand or model purchased by the owner was different than the brand or model that was the subject of the recall).  If the item of motor vehicle equipment was repaired, the reimbursement provisions identified above for vehicles will apply.

Ford notes that costs incurred by the owner within the period during which Ford’s original or extended warranty would have provided for a free repair of the problem will not be eligible for reimbursement, as provided by Part 573.13 (d)(1).

 

Entities Authorized to Provide Reimbursement

Ford will continue to use authorized dealers to reimburse owners under the specific reimbursement plans for a particular recall, and will encourage owners to pursue requests for reimbursement directly through dealers to expedite reimbursement.  Ford will also provide a mailing address to which customers can, at their option, send requests for reimbursement directly to Ford, as previously noted.  Requests for reimbursement sent directly to Ford may take up to 60 days to process.  Whether the owner chooses to pursue reimbursement requests through a dealer or directly through Ford, the owner will be directed to submit the required documentation, upon which reimbursement eligibility will be determined.

 

Required Documentation

The reimbursement determination will depend upon the information provided by the customer.  Consistent with Part 573.13 (d)(4) the following information must be submitted:

  • Claimant name and address
  • Vehicle make, model, and model year
  • Vehicle identification number (VIN) and, for replacement equipment, a description of such equipment or, for tires, the model, size and TIN (DOT code)
  • Identification of the recall number (either the Ford recall number or the NHTSA recall number)
  • Identification of the owner of the recalled vehicle at the time that the pre-notification remedy was obtained
  • An original receipt for the pre-notification remedy that includes a breakdown of the amount for parts, labor, other costs and taxes, including costs for the replacement item. Where the receipt covers work other than to address the recall or noncompliance, Ford may require the claimant to separately identify costs that are eligible for reimbursement.
  • If the remedy was obtained during the warranty period, documentation indicating that the warranty was not honored or the warranty repair did not correct the problem related to the recall.

Failure to submit all of the above information may result in denial of the reimbursement request.

 

Additional Information

The Part 577 required owner notice will provide a toll-free telephone number through which specific information about the reimbursement plan can be requested from Ford.  This general reimbursement plan will be incorporated into notifications pursuant to Part 573.6 by reference.  Information specific to an individual recall also may be incorporated into the Part 573.6 notification.


December, 2014

* * * IMPORTANT SAFETY RECALL * * *
(PROGRAMA DE SEGURIDAD IMPORTANTE)

 

Safety Recall Notice 14S22 / NHTSA Recall 14V-682
Aviso de Revisión de Seguridad or Cumplimiento 14S22

 

Mr. John Sample
123 Main Street
Anywhere, USA 12345

 

This notice applies to your vehicle, 12345678901234567.

 

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.

Ford Motor Company has decided that a defect which relates to motor vehicle safety exists in your vehicle, with the Vehicle Identification Number shown above.

We apologize for this situation and want to assure you that, with your assistance, we will correct this condition.  Our commitment, together with your dealer, is to provide you with the highest level of service and support.

What is the issue? If your vehicle is operated in high corrosion areas for an extended period (where salt is used on the roadways during winter months), it is possible that salt and moisture may become trapped under the fuel tank mounting reinforcement brackets.  Over time, corrosion under these reinforcement brackets can spread to the fuel tank that can result in a fuel leak.  If a leak occurs, you may experience symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning indicator.  Fuel leakage in the presence of an ignition source may result in a fire.
What should you do?

Service Engine Soon Indicator

Service Engine Soon Indicator

If your vehicle exhibits symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning indicator, please contact your dealer and request a service appointment for diagnosis and repair relating to Safety Recall 14S22.  Provide the dealer with the Vehicle Identification Number (VIN) of your vehicle.  The VIN is printed near your name at the beginning of this letter.

If your vehicle does not exhibit these symptoms, Ford will notify you by mail when service parts are available, at which time a service appointment to perform this safety recall can be scheduled.

If you do not already have a servicing dealer, you can access www.Fordowner.com for dealer addresses, maps, and driving instructions.

Until this time, if you have any questions regarding this recall, including the most current part availability status or when to make a service appointment, feel free to contact Ford directly by calling 1-866-436-7332.  Representatives are available to answer your questions.

Please note:  Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.

What will Ford and your dealer do? When parts are available for Safety Recall 14S22, you will be notified by Ford Motor Company via mail to schedule a service appointment with your dealer to repair or replace the fuel tank.  Parts for 14S22 are anticipated to be available in the third quarter of 2015.

We apologize for any inconvenience these part shortages may cause you.  We are working closely with our suppliers to accelerate part availability.

In the meantime, if your vehicle exhibits symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning indicator, contact your dealer and request a service date for recall 14S22.

This repair will be completed free of charge (parts and labor).

How long will it take? The time needed for this repair is less than one-half day.  However, due to service scheduling requirements, your dealer may need your vehicle for a longer period of time.
Have you previously paid for this repair? If you have previously paid for a repair that addresses the issue described in this letter, you still need to have this recall performed to ensure the correct parts were used.

You may be eligible for a refund of previously paid repairs.  Refunds will only be provided for service related to repair or replacement of the fuel tank for fuel leaks caused by corrosion.  To verify eligibility and expedite reimbursement, give your paid original receipt to your dealer.

Refund requests may also be sent directly to Ford Motor Company.  To request your refund from Ford, send the refund request with all required documentation, including your original repair receipt (no photocopies), to

Ford Motor Company at P.O. Box 6251, Dearborn, Michigan 48121-6251.

Refund requests mailed to this address may take up to 60 days to process.  Your original receipt will be returned to you.

Detailed information regarding eligibility for Ford’s reimbursement program and documentation requirements may be obtained by contacting the Ford Customer Relationship Center at 1-866-436-7332.

What if you no longer own this vehicle? If you no longer own this vehicle, and have an address for the current owner, please forward this letter to the new owner.

You received this notice because government regulations require that notification be sent to the last known owner of record.  Our records are based primarily on state registration and title data, which indicate that you are the current owner.

Can we assist you further? If you have difficulties getting your vehicle repaired promptly and without charge, please contact your dealership’s Service Manager for assistance.

RETAIL OWNERS:  If you still have concerns, please contact the Ford  Motor Company Customer Relationship Center at 1-866-436-7332 and one of our representatives will be happy to assist you.  For the hearing impaired call 1-800-232-5952 (TDD).  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

If you wish to contact us through the Internet, our address is: www.Fordowner.com.

Para asistencia en Español: 

Si necesita ayuda o tiene alguna pregunta, por favor llame al Centro de Relación con Clientes al 1-866-436-7332 y presione 2 para Español.

FLEET OWNERS:  If you still have concerns, please contact the Fleet Customer Information Center at 1-800-34-FLEET, Option #3 and one of our representatives will be happy to assist you.  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

Or you may contact us through the Internet at www.fleet.ford.com.

If you are still having difficulty getting your vehicle repaired in a reasonable time or without charge, you may write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave. S.E., Washington, D.C.

20590 or call the toll free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1800-424-9153) or go to www.safercar.gov.  Reference NHTSA Safety Recall 14V-682.  

 

Thank you for your attention to this important matter.

Ford Customer Service Division


December, 2014

* * * IMPORTANT SAFETY RECALL * * *
(PROGRAMA DE SEGURIDAD IMPORTANTE)

 

Safety  Recall Notice 14S22 / NHTSA Recall 14V-682
Aviso de Revisión de Seguridad or Cumplimiento 14S22

 

Mr. John Sample
123 Main Street
Anywhere, USA 12345

 

This notice applies to your vehicle, 12345678901234567.

 

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.

The Lincoln Motor Company has decided that a defect which relates to motor vehicle safety exists in your vehicle, with the Vehicle Identification Number shown above.

We apologize for this situation and want to assure you that, with your assistance, we will correct this condition.  Our commitment, together with your dealer, is to provide you with the highest level of service and support.

What is the issue? If your vehicle is operated in high corrosion areas for an extended period (where salt is used on the roadways during winter months), it is possible that salt and moisture may become trapped under the fuel tank mounting reinforcement brackets.  Over time, corrosion under these reinforcement brackets can spread to the fuel tank that can result in a fuel leak.  If a leak occurs, you may experience symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning indicator.  Fuel leakage in the presence of an ignition source may result in a fire.
What should you do?

Service Engine Soon Indicator

Service Engine Soon Indicator

If your vehicle exhibits symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning indicator, please contact your dealer and request a service appointment for diagnosis and repair relating to Safety Recall 14S22.  Provide the dealer with the Vehicle Identification Number (VIN) of your vehicle.  The VIN is printed near your name at the beginning of this letter.

If your vehicle does not exhibit these symptoms, The Lincoln Motor Company will notify you by mail when service parts are available, at which time a service appointment to perform this safety recall can be scheduled.

If you do not already have a servicing dealer, you can access www.Lincolnowner.com for dealer addresses, maps, and driving instructions.

Until this time, if you have any questions regarding this recall, including the most current part availability status or when to make a service appointment, feel free to contact Lincoln directly by calling 1-866-436-7332.  Representatives are available to answer your questions.

Please note:  Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.

What will Lincoln and your dealer do? When parts are available for Safety Recall 14S22, you will be notified by The Lincoln Motor Company via mail to schedule a service appointment with your dealer to repair or replace the fuel tank.  Parts for 14S22 are anticipated to be available in the third quarter of 2015.

We apologize for any inconvenience these part shortages may cause you.  We are working closely with our suppliers to accelerate part availability.

In the meantime, if your vehicle exhibits symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning indicator, contact your dealer and request a service date for recall 14S22.

This repair will be completed free of charge (parts and labor).

 

How long will it take? The time needed for this repair is less than one-half day.  However, due to service scheduling requirements, your dealer may need your vehicle for a longer period of time.
Have you previously paid for this repair? If you have previously paid for a repair that addresses the issue described in this letter, you still need to have this recall performed to ensure the correct parts were used.

You may be eligible for a refund of previously paid repairs.  Refunds will only be provided for service related to repair or replacement of the fuel tank for fuel leaks caused by corrosion.  To verify eligibility and expedite reimbursement, give your paid original receipt to your dealer.

Refund requests may also be sent directly to The Lincoln Motor Company.  To request your refund from Lincoln, send the refund request with all required documentation, including your original repair receipt (no photocopies), to The Lincoln Motor Company at P.O. Box 6251, Dearborn, Michigan 48121-6251.  Refund requests mailed to this address may take up to 60 days to process.  Your original receipt will be returned to you.

Detailed information regarding eligibility for Lincoln’s reimbursement program and documentation requirements may be obtained by contacting the Customer Relationship Center at 1-866-436-7332.

What if you no longer own this vehicle? If you no longer own this vehicle, and have an address for the current owner, please forward this letter to the new owner.

You received this notice because government regulations require that notification be sent to the last known owner of record.  Our records are based primarily on state registration and title data, which indicate that you are the current owner.

Can we assist you further? If you have difficulties getting your vehicle repaired promptly and without charge, please contact your dealership’s Service Manager for assistance.

RETAIL OWNERS:  If you still have concerns, please contact our Customer Relationship Center at 1-866-436-7332 and one of our representatives will be happy to assist you.  For the hearing impaired call 1-800-232-5952 (TDD).  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

If you wish to contact us through the Internet, our address is:   www.Lincolnowner.com.

Para asistencia en Español: 

Si necesita ayuda o tiene alguna pregunta, por favor llame al Centro de Relación con Clientes al 1-866-436-7332 y presione 2 para Español.

FLEET OWNERS:  If you still have concerns, please contact the Fleet Customer Information Center at 1-800-34-FLEET, Option #3 and one of our representatives will be happy to assist you.  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

Or you may contact us through the Internet at www.fleet.ford.com.

If you are still having difficulty getting your vehicle repaired in a reasonable time or without charge, you may write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave. S.E., Washington, D.C.

20590 or call the toll free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1800-424-9153) or go to www.safercar.gov.  Reference NHTSA Safety Recall 14V-682.  

 

Thank you for your attention to this important matter.

The Lincoln Motor Company


September 2015

* * * IMPORTANT SAFETY RECALL * * *
(PROGRAMA DE SEGURIDAD IMPORTANTE)

 

Safety Recall Notice 14S22 / NHTSA Recall 14V-682
Aviso de Revisión de Seguridad 14S22

 

Mr. John Sample
123 Main Street
Anywhere, USA 12345

 

Your Vehicle Identification Number (VIN): 12345678901234567.

 

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.

Ford Motor Company has decided that a defect which relates to motor vehicle safety exists in your vehicle, with the Vehicle Identification Number shown above.

We apologize for this situation and want to assure you that, with your assistance, we will correct this condition.  Our commitment, together with your dealer, is to provide you with the highest level of service and support.

Why are you receiving this notice?

Service Engine Soon Indicator

Service Engine Soon

In December, 2014, Ford mailed you a letter regarding possible corrosion on your vehicle’s fuel tank, which can result in fuel leakage.  If a leak occurs, you may experience symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning indicator. Fuel leakage in       the presence of an ignition source may result in a fire.  We are pleased to inform you that parts are now available to repair your vehicle.
What will Ford and your dealer do? Ford Motor Company has authorized your dealer to inspect your vehicle’s fuel tank and either clean and treat the fuel tank with corrosion preventative measures or replace it if needed.  This service will be completed free of charge (parts and labor).
How long will it take? The time needed for this repair is less than one-half day.  However, due to service scheduling requirements, your dealer may need your vehicle for a longer period of time.
What should you do? Please call your dealer without delay and request a service date for Safety Recall 14S22.  Provide the dealer with the VIN of your vehicle, which is     printed near your name at the beginning of this letter.

If you do not already have a servicing dealer, you can access www.Fordowner.com for dealer addresses, maps, and driving instructions. Please note:  Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.

Have you previously paid for this repair? If you have previously paid for a repair that addresses the issue described in this letter, you still need to have this recall performed to ensure the correct parts were used.

You may be eligible for a refund of previously paid repairs.  Refunds will only be provided for service related to repair or replacement of the fuel tank for fuel leaks caused by corrosion.  To verify eligibility and expedite reimbursement, give your paid original receipt to your dealer.

Refund requests may also be sent directly to Ford Motor Company.  To request your refund from Ford, send the refund request with all required documentation, including your original repair receipt (no photocopies), to

Ford Motor Company at P.O. Box 6251, Dearborn, Michigan 48121-6251.

Refund requests mailed to this address may take up to 60 days to process.  Your original receipt will be returned to you.

Detailed information regarding eligibility for Ford’s reimbursement program and documentation requirements may be obtained by contacting the Ford Customer Relationship Center at 1-866-436-7332.

What if you no longer own this vehicle? If you no longer own this vehicle, and have an address for the current owner, please forward this letter to the new owner.

You received this notice because government regulations require that notification be sent to the last known owner of record.  Our records are based primarily on state registration and title data, which indicate that you are the current owner.

Can we assist you further? If you have difficulties getting your vehicle repaired promptly and without charge, please contact your dealership’s Service Manager for assistance.

RETAIL OWNERS:  If you still have concerns, please contact the Ford

Motor Company Customer Relationship Center at 1-866-436-7332 and one of our representatives will be happy to assist you.  For the hearing impaired call 1-800-232-5952 (TDD).  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

If you wish to contact us through the Internet, our address is: www.Fordowner.com.

Para asistencia en Español: 

Si necesita ayuda o tiene alguna pregunta, por favor llame al Centro de Relación con Clientes al 1-866-436-7332 y presione 2 para Español.

FLEET OWNERS:  If you still have concerns, please contact the Fleet Customer Information Center at 1-800-34-FLEET, Option #3 and one of our representatives will be happy to assist you.  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

Or you may contact us through the Internet at www.fleet.ford.com.

If you are still having difficulty getting your vehicle repaired in a reasonable time or without charge, you may write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave. S.E., Washington, D.C. 20590 or call the toll free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1800-424-9153) or go to www.safercar.gov.  Reference NHTSA Safety Recall 14V-682.

 

Thank you for your attention to this important matter.

Ford Customer Service Division


September 2015

* * * IMPORTANT SAFETY RECALL * * *
(PROGRAMA DE SEGURIDAD IMPORTANTE)

 

Safety Recall Notice 14S22 / NHTSA Recall 14V-682
Aviso de Revisión de Seguridad 14S22

 

Mr. John Sample
123 Main Street
Anywhere, USA 12345

 

Your Vehicle Identification Number (VIN): 12345678901234567.

 

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.

The Lincoln Motor Company has decided that a defect which relates to motor vehicle safety exists in your vehicle, with the VIN shown above.

We apologize for this situation and want to assure you that, with your assistance, we will correct this condition.  Our commitment, together with your dealer, is to provide you with the highest level of service and support.

Why are you receiving this notice?

Service Engine Soon Indicator

Service Engine Soon

In December, 2014, the Lincoln Motor Company mailed you a letter regarding possible corrosion on your vehicle’s fuel tank, which can result in fuel leakage. If a leak occurs, you may experience symptoms of a fuel odor, fuel on the ground, or illumination of the “Service Engine Soon” warning        indicator. Fuel leakage in the presence of an ignition source may result in a fire. We are pleased to inform you that parts are now available to repair your vehicle.
What will Lincoln and your dealer do? The Lincoln Motor Company has authorized your dealer to inspect your vehicle’s fuel tank and either clean and treat the fuel tank with corrosion preventative measures or replace it if needed.  This service will be completed free of charge (parts and labor).
How long will it take? The time needed for this repair is less than one-half day.  However, due to service scheduling requirements, your dealer may need your vehicle for a longer period of time.
What should you do? Please call your dealer without delay and request a service date for Safety Recall 14S22.  Provide the dealer with the VIN of your vehicle, which is     printed near your name at the beginning of this letter.

If you do not already have a servicing dealer, you can access www.Lincolnowner.com for dealer addresses, maps, and driving instructions. Please note:  Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.

Have you previously paid for this repair? If you have previously paid for a repair that addresses the issue described in this letter, you still need to have this recall performed to ensure the correct parts were used.

You may be eligible for a refund of previously paid repairs.  Refunds will only be provided for service related to repair or replacement of the fuel tank for fuel leaks caused by corrosion.  To verify eligibility and expedite reimbursement, give your paid original receipt to your dealer.

Refund requests may also be sent directly to The Lincoln Motor Company.  To request your refund from Lincoln, send the refund request with all required documentation, including your original repair receipt (no photocopies), to The Lincoln Motor Company at P.O. Box 6251, Dearborn, Michigan 48121-6251.  Refund requests mailed to this address may take up to 60 days to process.  Your original receipt will be returned to you.

Detailed information regarding eligibility for Lincoln’s reimbursement program and documentation requirements may be obtained by contacting the Customer Relationship Center at 1-866-436-7332.

What if you no longer own this vehicle? If you no longer own this vehicle, and have an address for the current owner, please forward this letter to the new owner.

You received this notice because government regulations require that notification be sent to the last known owner of record.  Our records are based primarily on state registration and title data, which indicate that you are the current owner.

Can we assist you further? If you have difficulties getting your vehicle repaired promptly and without charge, please contact your dealership’s Service Manager for assistance.

RETAIL OWNERS:  If you still have concerns, please contact our Customer Relationship Center at 1-866-436-7332 and one of our representatives will be happy to assist you.  For the hearing impaired call 1-800-232-5952 (TDD).  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

If you wish to contact us through the Internet, our address is:   www.Lincolnowner.com.

Para asistencia en Español: 

Si necesita ayuda o tiene alguna pregunta, por favor llame al Centro de Relación con Clientes al 1-866-436-7332 y presione 2 para Español.

FLEET OWNERS:  If you still have concerns, please contact the Fleet Customer Information Center at 1-800-34-FLEET, Option #3 and one of our representatives will be happy to assist you.  Representatives are available Monday through Friday:  8:00AM – 8:00PM (Eastern Time).

Or you may contact us through the Internet at www.fleet.ford.com.

If you are still having difficulty getting your vehicle repaired in a reasonable time or without charge, you may write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave. S.E., Washington, D.C. 20590 or call the toll free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1800-424-9153) or go to www.safercar.gov.  Reference NHTSA Safety Recall 14V-682.

 

Thank you for your attention to this important matter.

The Lincoln Motor Company


 

Bestseller No. 1
CRC GDI IVD Intake Valve & Turbo Cleaner
  • Proven to clean intake valves on GDI engines and turbo systems
  • Easily installed through the air intake system
  • Highest concentration PEA (Polyether Amine) detergency available
  • Proven to remove up to 46% of GDI Intake Valve deposits in 1 hour
  • 150X more concentrated than fuel additives
Bestseller No. 2
Gumout 540028 Foaming Intake Valve & Turbo Cleaner, 11 oz
  • Deep Cleans GDI (Gasoline Direct Injection) / PFI (Port Fuel Injection) Intake Valves, As Well As, The Throttle Body, Intake Ports, Fuel Injectors and Combustion Chambers
  • Helps Restore Fuel Economy and Maximize Horse Power
  • Removing Carbon and Fuel Deposits From Gasoline Engines Intake Valves, Intake Ports and Turbos Is Essential to Ensuring Optimal Vehicle Performance.
  • Made with Carbon Clear and Trade, the Most Advanced P.E.A. Cleaning Agent Available
  • Strong Enough to Cut Through Thick Carbon Deposits, Even at Extreme Engine Temperatures
Bestseller No. 3
Bestseller No. 4
Bestseller No. 5
FIRSTINFO A1601 4 In 1 Intake Valve Cleaner Combustion Chamber Cleaner/Vacuum System Cleaner/Vacuum System Pressure Tester Kit
  • 【 Maintain Engine Performance 】 Perfect for air intake system, combustion chamber, EGR Valves, intake valves and oxygen sensors. Easy operation for making the fuel injectors spray smoothly and properly.
  • 【 Easy to Use 】 Simply fill with air intake cleaning liquids and connect the vacuum hose of vehicle vacuum system. Reduce carbon deposits easily.
  • 【 Multiple Applications 】 Use to clean the intake valve, combustion chamber, vacuum system and test the vacuum system pressure. Provides more thorough cleaning than other methods. Effectively remove engine carbon deposits and increase gas mileage performance.
  • 【 Equipped with Negative Pressure Gauge 】 The liquid-filled gauge for accurate vacuum pressure reading and monitoring chemical flow.
  • 【 Gasoline Engine / Petrol Cars Use 】 Used for gasoline engine injection and petrol cars. "NOT" for diesel injector. And solution liquid is "NOT" included.
Bestseller No. 6
Bestseller No. 7
Berryman Products 2611 Intake Valve and Combustion Chamber Cleaner, 16-Ounce Aerosol
  • Formulated for Use In All Fuel-Injected Gasoline Engines, Including GDI
  • Contains Polyetheramine (“PEA”) to Dissolve Carbon Buildup in Combustion Chambers
  • Cleans ALL Types of Intake Valves, Including Those Found in PFI, TBI, and GDI Engines
  • Safe On Catalytic Converters and Oxygen Sensors
  • Not For Use In Diesel Engines
Bestseller No. 8
CRC Industries, Inc. Intake Valve Cleaner (11 oz) Bundled with Latex Gloves (3 Items)
  • Bundle comes with:
  • 2 - CRC 05319 Industries Intake Valve Cleaner (11 oz)
  • 2 Pairs (4 Gloves) of CLC2316L Latex Gloves - Large
  • Fit type: Universal
Bestseller No. 9
New Turbo II Model 46 Pre-Cleaner with 6" Inlet/Air Intake & 350 to 700 CFM
  • One New Replacement Turbo Ii Pre-Cleaner.
  • Fits Model 46
  • Inlet Size: 6" And Operating Range: 350-700 Cfm
  • Powered by Intake Air, Installs in Seconds, Saves Money, Extends Air Filter Life, Saves Fuel
  • Protects Your Engine and Saves Servicing Time
Bestseller No. 10
Smilyeez BG GDI Air Intake & Valve Cleaner PN 260 With Pocket Screwdriver (1)
  • Restores MPG
  • Restores engine performance
  • Restores power
  • Reduces harmful emissions
  • Requires pressurized tool

Last update on 2024-03-23 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

4 thoughts on “14S22 – Fuel Tank Corrosion Inspection and Repair – 2007-2008 Ford & Lincoln”

  1. My dealer is trying to make me pay to replace potential damage resulting from replacing the fuel tank including potentially the fuel pump assembly. They will not complete the recall until I agree to pay as they say the recall does not cover rust. It is my understanding that the recall must be completed at no charge no matter what is required to complete the recall. Is that correct?

    Reply
  2. Hi! I just purchased a 2007 Ford Edge that is included in this recall but the recall was never repaired/replaced and dealer states I have to take it to a ford dealership to get the recall fixed. The recall is still in effect and able to be fixed now correct? I have an appointment to take it to the Ford dealership next week for the recall.

    Reply

Leave a Reply to oemdtc Cancel reply

Share to...